AVSPARE.COM
parts catalog

FRAME AS-UPPER 3302634 - Caterpillar


3302634 FRAME AS-UPPER Caterpillar parts 349E, 349E L, 349E L VG
Rating:
66
Alternative (cross code) number:
CA3302634
330-2634
3302634
Caterpillar 3302634 FRAME AS-UPPER

Buy FRAME AS-UPPER 3302634 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, MOBILE HYD POWER UNIT,

Compatible equipment models: 3302634:

EXCAVATOR  349E L   349E L VG  
MOBILE HYD POWER UNIT  349E   Caterpillar
Number on catalog scheme: 9
  For full view, you need register

Information:


Illustration 1 g02000893
Schematic of the Cat Data Link
This diagnostic code is recorded when the Transmission ECM is not sending the necessary parameters to the monitoring system at the proper rate. The update rate for parameters that are generated by the Transmission ECM is not correct. The communication failure may be due to disconnected connectors or a faulty wiring harness.The possible causes of this diagnostic code are listed below:
Software is installed on the transmission ECM that is not correct.
Software is installed on the monitoring system that is not correct.
Incompatible software may be installed.
The transmission ECM has the wrong software.
The transmission ECM has generated this diagnostic code in error.Note: If the monitoring system is not operating correctly, refer to the "System Operation" manual for this machine for information on troubleshooting the monitoring system. Ensure that the diagnostic code is active before performing this procedure. Check the monitoring system for correct operation before performing this procedure.Test Step 1. CHECK THE TRANSMISSION ECM AND THE IMPLEMENT ECM FOR PROPER SOFTWARE VERSIONS.
Use Caterpillar Electronic Technician (ET) in order to verify that the versions of software are compatible. Note: Consult your Caterpillar Dealer for the correct part numbers of the flash software.Expected Result:The proper versions of software are installed on the Transmission ECM and the Implement ECM.Results:
OK - The versions of software are compatible. Proceed to Test Step 2.
NOT OK - The proper software is not installed.Repair: Flash the proper software to the appropriate ECM. Cycle the keyswitch in order to initialize the new software. Ensure that the diagnostic code is no longer active.STOPTest Step 2. RECHECK FOR DIAGNOSTIC CODES.
Ensure that the diagnostic code is active. Expected Result:The diagnostic code is inactive. The diagnostic code indicator is inactive.Results:
OK - The diagnostic code is inactive. The diagnostic code indicator is inactive.Repair: Clear the diagnostic code.STOP
NOT OK - The diagnostic code is active.Repair: Ensure that the proper software is installed. If the software is correct, the Transmission ECM may have generated this diagnostic code in error.Exit this procedure. Perform this procedure again. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP

Caterpillar parts catalog:

Caterpillar parts catalog
349E L Excavators KFX00001-UP (MACHINE) POWERED BY C13 Engine
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
349E L-VG Excavators DGE00001-UP (MACHINE) POWERED BY C13 Engine
349E Mobile Hydraulic Power Unit S3P00001-UP (MACHINE) POWERED BY C13 Engine


Parts frame Caterpillar catalog:

3T3418 FRAME AS-END
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
3835556 FRAME AS
312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 324E L, ...
3629748 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L
3387744 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG
3387746 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG
3387747 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L
3591468 FRAME AS-UPPER
349E, 349E L, 349E L VG
3325118 FRAME AS-CARBODY
349D L, 349E, 349E L, 349E L VG
3387747 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L
3387746 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG
3387744 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG
3629748 FRAME AS
349E, 349E L, 349E L HVG, 349E L VG, 349F L
3591468 FRAME AS-UPPER
349E, 349E L, 349E L VG
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.