AVSPARE.COM
parts catalog

FRAME A 4Z8471 - Caterpillar



4Z8471 FRAME A Caterpillar parts FRAME
Rating:
51
Alternative (cross code) number:
CA4Z8471
4Z-8471
4Z8471
Caterpillar 4Z8471 FRAME A
Weight: 41 pounds 18 kg.

Buy FRAME A 4Z8471 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 2 g02535237
Tooling (C)
Illustration 3 g02156033
Tooling group (D)
Table 3
Tool Item Qty Part
Number Description
A 198-4240 Digital Pressure Indicator Gp
A1 1 198-4234 Indicator
A2 1 198-4237 Pressure Sensor
34,450 kPa (5,000 psi)
A3 1 198-4236 Extension Cable
C 348-5430 Multi-Tool Gp
C1 1 285-0908 Multi-Tool
C2 1 6V-2198 Cable As
C3 1 9U-5140 Photo Pickup
C4 1 6V-3137 Base
C5 1 1U-6605 Reflective Tape
C6 1 6V-3138 Extension
D D1 1 6V-7788 Flow Meter
5 to 60 L/min (2 to 15 US gpm)
D2 1 8C-6874 Reducer
D3 1 6V-9746 O-Ring Seal
D4 1 124-1901 Permanent Coupling
D5 3 ft 122-6870 Bulk Hydraulic Hose
D6 1 124-2147 Permanent Coupling
D7 1 6V-8942 O-Ring Reducer
D8 1 6V-8556 Nut
D9 1 6V-8398 O-Ring Seal
F 1 311-1362 Vacuum Cap Machine Preparation
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Note: Set the pilot relief valve to the specification. Refer to Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust".
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 4 g03648360
Flow meter tool layout
Tooling (D)
( 1) Pilot pump
(2) Connector
(3) Hose
(4) Pilot filter
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 4.
Disconnect hose (3) from connector (2).
Connect flow meter assembly (D) between connector (2) and hose (3). Note: Correct orientation of the flow meter is necessary. The oil flows from pilot pump (1) to pilot filter (4).
Remove 311-1362 Vacuum Cap.
Install tooling (C) on the engine to monitor engine speed. Test Procedure
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Check the flow of oil through the flow meter. Refer to Table 1.


Parts frame Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.