6V9733 FRONT STRUCTURE Caterpillar parts
245, 245B, 621E, 623E, 980C
Rating:
Alternative (cross code) number:
CA6V9733
6V-9733
6V9733
CA6V9733
6V-9733
6V9733
Weight: 2 pounds 0 kg.
EXCAVATOR, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$121.59
20 Jan 2024
US: FinditParts Inc
6V9733 - KIT GASKET COV & fits Caterpillar (CAT)
BLUMAQ 6V9733 - KIT GASKET COV & fits Caterpillar (CAT)
BLUMAQ 6V9733 - KIT GASKET COV & fits Caterpillar (CAT)
$99.84
18 Oct 2023
US: FinditParts Inc
6V9733 - KIT GASKET COV & fits Caterpillar (CAT)
BLUMAQ 6V9733 - KIT GASKET COV & fits Caterpillar (CAT)
BLUMAQ 6V9733 - KIT GASKET COV & fits Caterpillar (CAT)
$127.81
11 Oct 2021
3.2[1.44] Pounds
US: Highway And Hea
6V9733 | Front Structure Gasket Set
HHP HIGHWAY & HEAVY PARTS HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Image(s) is for illustration purposes only and may not represent the actual part. || Products are only sourced from quality certified manufacturing facilities.
HHP HIGHWAY & HEAVY PARTS HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Image(s) is for illustration purposes only and may not represent the actual part. || Products are only sourced from quality certified manufacturing facilities.
For full view, you need register
Compatible equipment models: 6V9733:
Information:
Probable Causes
Low quality fuel
Engine speed/timing sensor
Electrical connectors
Injector
Not enough lubrication
Too much valve lash
Damage to valve train components
Failure of connecting rod bearingRecommended Actions
Low Quality Fuel
Refer to Operation and Maintenance Manual for information on the proper characteristics of the fuel. Obtain a fuel analysis.Engine Speed/Timing Sensor
Calibrate the engine speed/timing sensor if a CID-FMI 261-13 Engine Timing calibration required diagnostic code is active. Refer to the calibration procedure Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".Electrical Connectors
Check for the correct installation of the connector(s) for the Electronic Control Module (ECM) J1/P1 and/or J2/P2. Check for correct installation of the applicable fuel injector connectors. Repair the connector and/or replace the connector. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors".Injector
Use Caterpillar Electronic Technician (ET) to determine if any diagnostic codes for the injector solenoids are present. Perform the "Injector Solenoid Test". Observe that the injector solenoids are being energized on Cat ET. Check injector height setting. Perform the "Cylinder Cutout Test". Locate the misfiring cylinder. Refer to the diagnostic functional test Troubleshooting, "Injector Solenoids".Not Enough Lubrication
Check the lubrication in the valve compartment. Check for sufficient lubrication between the injector tappet and the rocker arm buttons. Check for blocked oil passages. Oil passages must be clean. Ensure that the oil passages that send oil to the cylinder heads are clean.Valve Lash
Check the valve lash. Refer to the diagnostic procedure Troubleshooting, "Too Much Valve Lash".Damage to Valve Train Components
Remove the valve cover from the suspect cylinder(s). Check the following items for damage: camshaft, valve rotocoil, valve springs, lifters, pushrods, and bridges. Check for valves that do not move freely. Remove the cylinder head. Inspect the valves. Replace any damaged parts.Failure of Connecting Rod Bearing
Inspect the connecting rod bearings and the bearing surfaces (journals) on the crankshaft. Check the piston pin for excessive wear. Replace any damaged parts.
Low quality fuel
Engine speed/timing sensor
Electrical connectors
Injector
Not enough lubrication
Too much valve lash
Damage to valve train components
Failure of connecting rod bearingRecommended Actions
Low Quality Fuel
Refer to Operation and Maintenance Manual for information on the proper characteristics of the fuel. Obtain a fuel analysis.Engine Speed/Timing Sensor
Calibrate the engine speed/timing sensor if a CID-FMI 261-13 Engine Timing calibration required diagnostic code is active. Refer to the calibration procedure Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".Electrical Connectors
Check for the correct installation of the connector(s) for the Electronic Control Module (ECM) J1/P1 and/or J2/P2. Check for correct installation of the applicable fuel injector connectors. Repair the connector and/or replace the connector. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors".Injector
Use Caterpillar Electronic Technician (ET) to determine if any diagnostic codes for the injector solenoids are present. Perform the "Injector Solenoid Test". Observe that the injector solenoids are being energized on Cat ET. Check injector height setting. Perform the "Cylinder Cutout Test". Locate the misfiring cylinder. Refer to the diagnostic functional test Troubleshooting, "Injector Solenoids".Not Enough Lubrication
Check the lubrication in the valve compartment. Check for sufficient lubrication between the injector tappet and the rocker arm buttons. Check for blocked oil passages. Oil passages must be clean. Ensure that the oil passages that send oil to the cylinder heads are clean.Valve Lash
Check the valve lash. Refer to the diagnostic procedure Troubleshooting, "Too Much Valve Lash".Damage to Valve Train Components
Remove the valve cover from the suspect cylinder(s). Check the following items for damage: camshaft, valve rotocoil, valve springs, lifters, pushrods, and bridges. Check for valves that do not move freely. Remove the cylinder head. Inspect the valves. Replace any damaged parts.Failure of Connecting Rod Bearing
Inspect the connecting rod bearings and the bearing surfaces (journals) on the crankshaft. Check the piston pin for excessive wear. Replace any damaged parts.
Caterpillar parts catalog:
Parts front Caterpillar catalog:
5P8368
FRONT STRUCTURE
245, 983B
245, 983B
6V2975
FRONT STRUCTURE
245, 621B, 623B
245, 621B, 623B
824C, 825C, 826C, 980C
5P8368
FRONT STRUCTURE
245, 983B
245, 983B
3412, D9N
225, 227, 3208, 613B
3406B
215, 943, 953, D3B
215, 943, 953
12G, 140G, 14G, 235, 815, 816
12G, 215, 225, 235, 955L, D4D, D4E, D5B, D6D