AVSPARE.COM
parts catalog

GAGE 0005509 - Caterpillar



0005509 GAGE Caterpillar parts GAGE
Rating:
66
Alternative (cross code) number:
CA0005509
000-5509
0005509
Caterpillar 0005509 GAGE

Buy GAGE 0005509 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (-) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Required Parts
Table 1
Required Part for Ether Starting Aid    
Item     Qty     Part Number     Description    
(1)     1     187-3971     Elbow    
(2)     1     228-0931     Ether Starting Aid Gp    
(3)     1     229-8740     Harness    
(4)     1     196-9852     Plate As    
(5)     1     7N-0296     Ether Cylinder As    
(6) (1)     1     228-4281     Software    
(7) (2)     1     228-4280     Software    
(8)     3     8T-4193     Bolt    
(9)     3     9X-8257     Washer    
( 1 ) Use this item on machines with (S/N: BLE) and (S/N: BLT).
( 2 ) Use this item on machines with (S/N: BNC), (S/N: DAE), (S/N: BMJ), and (S/N: BMY). Installation Instructions
Remove the inlet manifold and the heater. Refer to the Disassembly and Assembly Manual, SENR9502, "Inlet Manifold-Remove" for more information on this topic.
Separate the air inlet heater from the air inlet manifold.Note: Be careful not to damage the coil for the air inlet heater during separation.
Remove inlet air temperature sensor (13) and discard the former inlet manifold.
Illustration 1 g01040324
Install inlet air temperature sensor (13) in the new inlet elbow (1) .
Install ether nozzle (14) from the ether starting aid group (2) into the new air inlet elbow (1) .Note: The jet in the ether nozzle should point away from the engine.
Install the air inlet manifold and the heater onto the engine. Refer to the Disassembly and Assembly Manual, SENR9502, "Inlet Manifold-Install" for more information on this topic.
Illustration 2 g01035774
Illustration 3 g01035724
Install plate assembly (2) from the ether starting aid group on the engine with bolts (8) and washers (9). Refer to Illustration 2 and Illustration 3 for the location of components.
Ground wiring harness (3) for ether starting aid group (2) to the bolt with clip (10) .
Route harness (3) for the ether starting aid along the front left side of the engine. Harness (3) should be routed with the main wiring harness to the rear connector of the engine ECM.
Remove the rear 70-pin connector from the engine ECM.
Move the wire in socket 15 to socket 17.
Install the wires from harness (3) of the ether starting aid into the appropriate locations in the 70-pin connector.Note: Socket locations are already specified on the wires.
Reconnect the rear 70-pin connector to the engine ECM.
Illustration 4 g01035779
Remove 196-9852 Plate As from the fire wall.
Install ether starting aid relay (11) from ether starting aid group (2) onto new 196-9852 Plate As


Parts gage Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.