8T3149 GAGE-PLUG Caterpillar parts
Rating:
Alternative (cross code) number:
CA8T3149
8T-3149
8T3149
CA8T3149
8T-3149
8T3149
Weight: 0.010 pounds 0 kg.
Information:
1. Drain the coolant to a level below elbow (1).2. Remove four bolts (2) and elbow (1). Remove gaskets from elbow. 3. Remove bolt (3) that holds fuel injection lines to regulator housing bonnet. Remove the three bolts (4) that hold water temperature regulator housing to engine. Remove water temperature regulator and housing (5) and gasket.Install Water Temperature Regulators And Housings
1. Install a new gasket (1) on regulator housing (2). Put the water temperature regulator and housing (2) in position on the engine. 2. Install new gaskets on water line and regulator housing. Install elbow (3) with the four bolts that hold it. Install bolt (4) that holds fuel injection lines to the regulator housing bonnet.3. Fill the cooling system with coolant to the correct level. See LUBRICATION AND MAINTENANCE GUIDE.Disassemble Water Temperature Regulators And Housings
start by:a) remove water temperature regulators and housings 1. Remove bolts (3) and make a separation between tube (1) and regulator housing (5). Remove gasket (2).2. Remove regulator (4) from the housing. 3. Remove seal (6) from the regulator housing with tool group (A).Assemble Water Temperature Regulators And Housings
1. Put a small amount of clean engine oil on the seal. Install the seal in the housing with tool group (A). Install the seal until it makes contact with the counterbore in the housing and with the lip of the seal away from the regulator. 2. Install regulator (4) in the housing.3. Install a new gasket (2) between regulator housing and tube (1). Install bolts (3) that hold tube and housing together.end by:a) install water temperature regulators and housings
1. Install a new gasket (1) on regulator housing (2). Put the water temperature regulator and housing (2) in position on the engine. 2. Install new gaskets on water line and regulator housing. Install elbow (3) with the four bolts that hold it. Install bolt (4) that holds fuel injection lines to the regulator housing bonnet.3. Fill the cooling system with coolant to the correct level. See LUBRICATION AND MAINTENANCE GUIDE.Disassemble Water Temperature Regulators And Housings
start by:a) remove water temperature regulators and housings 1. Remove bolts (3) and make a separation between tube (1) and regulator housing (5). Remove gasket (2).2. Remove regulator (4) from the housing. 3. Remove seal (6) from the regulator housing with tool group (A).Assemble Water Temperature Regulators And Housings
1. Put a small amount of clean engine oil on the seal. Install the seal in the housing with tool group (A). Install the seal until it makes contact with the counterbore in the housing and with the lip of the seal away from the regulator. 2. Install regulator (4) in the housing.3. Install a new gasket (2) between regulator housing and tube (1). Install bolts (3) that hold tube and housing together.end by:a) install water temperature regulators and housings
Parts gage Caterpillar catalog:
8T3148
GAGE-PLUG
Caterpillar
Caterpillar
8T3147
GAGE-PLUG
Caterpillar
Caterpillar
8T3146
GAGE-PLUG
Caterpillar
Caterpillar
8T3145
GAGE-PLUG
Caterpillar
Caterpillar
8T3144
GAGE-PLUG
Caterpillar
Caterpillar
8T3114
GAGE-PRESSURE
Caterpillar
Caterpillar
8T5166
GAGE-PRESS
Caterpillar
Caterpillar
8T5113
GAGE-CUTTER
Caterpillar
Caterpillar
8T4557
GAGE
Caterpillar
Caterpillar
8T3219
GAGE G
Caterpillar
Caterpillar
8T3217
GAGE
Caterpillar
Caterpillar
8T3150
GAGE G-
Caterpillar
Caterpillar