1352377 GASKET & SEAL KITS Caterpillar parts
320B, 320N
Rating:
Alternative (cross code) number:
CA1352377
135-2377
1352377
CA1352377
135-2377
1352377
Weight: 0.08 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$69.44
21 Mar 2019
Unknown: Unknown
Caterpillar 1352377 GSK KT-F.I New
Number on catalog scheme:
For full view, you need register
Information:
Note: Some white smoke may be present during cold start-up conditions when the engine is operating normally. If the white smoke persists, there may be a problem.Probable Causes
Coolant temperature sensor
Water temperature regulators
Engine speed/timing
Unit injectors
Personality module
Fuel supply
Component wear
Cooling systemRecommended Actions
Coolant Temperature Sensor
Use the Caterpillar Electronic Technician (Cat ET) to verify that the engine has exited cold mode.
Compare the coolant temperature from Cat ET to the coolant temperature that is obtained from the 6V-9130 Temperature Adapter .Water Temperature Regulators
Check the water temperature regulators for correct operation. Refer to Testing and Adjusting, "Cooling System" for the proper procedure.
If necessary, replace the water temperature regulators. Refer to Disassembly and Assembly, "Water Temperature Regualtor - Remove and Install" for more information.Engine Speed/Timing
Check the calibration of the engine speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
Verify that the crankshaft and camshaft drive gears are set with the proper orientation. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".Unit Injectors
Perform the Cylinder Cutout Test on Cat ET in order to try to isolate any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid Circuit - Test".
Cut out the individual cylinder for 30 seconds to 1 minute. Verify that the smoke decreases.Personality Module
Verify that the correct personality module (flash file) is installed. Refer to Troubleshooting, "Programming Parameters".Fuel Supply
Inspect the fuel system components.
Check for correct fuel pressure.
Check fuel quality. Low cetane fuel can create white smoke. Replace the fuel with a higher cetane fuel. In temperatures below 0 °C (32 °F), check for solidified fuel (wax). Refer to Special Instruction, SEBD0717, "Diesel Fuels And Your Engine".
If necessary, replace the fuel with a higher cetane fuel.Component Wear
Check the engine for the following problems: Excessive valve wear, piston wear, ring wear, liner wear and reduced compression pressure.Cooling System
Check for an internal coolant leak into the cylinder and/or the exhaust. Refer to Testing and Adjusting, "Cooling System".
Coolant temperature sensor
Water temperature regulators
Engine speed/timing
Unit injectors
Personality module
Fuel supply
Component wear
Cooling systemRecommended Actions
Coolant Temperature Sensor
Use the Caterpillar Electronic Technician (Cat ET) to verify that the engine has exited cold mode.
Compare the coolant temperature from Cat ET to the coolant temperature that is obtained from the 6V-9130 Temperature Adapter .Water Temperature Regulators
Check the water temperature regulators for correct operation. Refer to Testing and Adjusting, "Cooling System" for the proper procedure.
If necessary, replace the water temperature regulators. Refer to Disassembly and Assembly, "Water Temperature Regualtor - Remove and Install" for more information.Engine Speed/Timing
Check the calibration of the engine speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
Verify that the crankshaft and camshaft drive gears are set with the proper orientation. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".Unit Injectors
Perform the Cylinder Cutout Test on Cat ET in order to try to isolate any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid Circuit - Test".
Cut out the individual cylinder for 30 seconds to 1 minute. Verify that the smoke decreases.Personality Module
Verify that the correct personality module (flash file) is installed. Refer to Troubleshooting, "Programming Parameters".Fuel Supply
Inspect the fuel system components.
Check for correct fuel pressure.
Check fuel quality. Low cetane fuel can create white smoke. Replace the fuel with a higher cetane fuel. In temperatures below 0 °C (32 °F), check for solidified fuel (wax). Refer to Special Instruction, SEBD0717, "Diesel Fuels And Your Engine".
If necessary, replace the fuel with a higher cetane fuel.Component Wear
Check the engine for the following problems: Excessive valve wear, piston wear, ring wear, liner wear and reduced compression pressure.Cooling System
Check for an internal coolant leak into the cylinder and/or the exhaust. Refer to Testing and Adjusting, "Cooling System".
Caterpillar SIS machinery equipment:
Parts gasket Caterpillar catalog:
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120M, 120M 2, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14M, 160H,...
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 311, 311B, 311C, 311D LRR, 312, 312B, 3...
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 303.5C, 3044C, 304D CR, 305.5D, 305C CR, 311, ...
311, 312, 315, 315B, 315C, 317B LN, 318B, 318C, 319C, 320, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 32...
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E450
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN, E110, E110B, E120B, E200B, E450
318C, 319C, 320 L, 320B, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321B, 321C, 321D LCR, 323D L, 323D LN, 323D SA
318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN, E200B
320B, 320N
1352379
GASKET & SEAL KITS
311, 311B, 312, 312B, 320B, 320N
311, 311B, 312, 312B, 320B, 320N
1414375
GASKET & SEAL KITS
311, 311B, 312, 312B
311, 311B, 312, 312B
311B, 312B
311B, 312B
