GASKET 1958266 - Caterpillar

1958266 GASKET Caterpillar parts 301.6C, 304, 305

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1958266
195-8266
1958266

Weight: 0.01 pounds 0 kg.

Buy GASKET 1958266 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

This part in 1 request: Show. This information for suppliers only!

#520692 1958266

2020-09-04

Compatible equipment models: 1958266:

MINI HYD EXCAVATOR 301.6C 304 305 Caterpillar

Number on catalog scheme:

For full view, you need register

Information:

Illustration 1 g00866238
Schematic for the fuel level sender
This diagnostic code is recorded when the main display module reads the signal voltage of the fuel level sender and the voltage is too low. The possible causes of this failure are listed here:
The sender has failed.
The signal circuit in the machine harness is shorted to ground.
The main display module has failed. This is unlikely. This failure causes the fuel gauge to always indicate an empty fuel tank or the fuel gauge may intermittently indicate an empty fuel tank. Test Step 1. CHECK THE SENDER.
Disconnect the machine harness from the sender. Expected Result:The diagnostic code changes from CID 0096 FMI 04 to CID 0096 FMI 03.Results:
OK - The diagnostic code changed from CID 0096 FMI 04 to CID 0096 FMI 03. This indicates that the failure is no longer present. The sender has failed. Repair: Replace the sender.STOP
NOT OK - The diagnostic code remains. The failure remains present. The sender is not causing the failure. Proceed to test step 2.Test Step 2. CHECK THE HARNESS.
The sender remains disconnected from the machine harness.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the J1 machine harness connector from the main display module.
At the machine harness connector for the sender, measure the resistance between the signal contact 1 (wire 447-PK(Pink)) and frame ground. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. The main display module has failed. Repair: It is unlikely that the ECM has failed. Exit this procedure, and perform this procedure again. If the failure is not found, replace the ECM. See Testing and Adjusting, " Module - Replace". STOP
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. There is a short between frame ground and the signal circuit in the machine harness. Repair: Repair the machine harness or replace the machine harness. STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

305CR Mini Hydraulic Excavator DSA00001-UP (MACHINE) POWERED BY K4N Engine

196-8314: PAN GP-OIL » SEBP32920019
195-8435: PUMP GP-ENGINE OIL » SEBP32920023

304CR Mini Hydraulic Excavator NAD00001-UP (MACHINE) POWERED BY S4L2 Engine

196-8314: PAN GP-OIL » SEBP36740040
356-8188: PAN GP-OIL » SEBP36740042
195-8435: PUMP GP-ENGINE OIL » SEBP36740051

305CR Mini Hydraulic Excavator DGT00001-UP (MACHINE) POWERED BY K4N Engine

196-8314: PAN GP-OIL » SEBP40980020
195-8435: PUMP GP-ENGINE OIL » SEBP40980024

301.6C & 301.8C Mini Hydraulic Excavators JBB00001-UP (MACHINE) POWERED BY L3E Engine

223-0420: GEAR GP-FRONT » SEBP42290028
265-7843: PAN GP-OIL » SEBP42290032

Parts gasket Caterpillar catalog:

1U8846 GASKET-LIQUID
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120M, 120M 2, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14M, 160H,...

1117899 GASKET
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...

5I7628 GASKET
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 302.5C, 303, 303.5C, 303.5D, 303C CR, 304, 304...