1M7821 GASKET Caterpillar parts
120, 12E, 12F, 140, 14E, 920, 930
Rating:
Alternative (cross code) number:
CA1M7821
1M-7821
1M7821
CA1M7821
1M-7821
1M7821
Weight: 0.11 pounds 0 kg.
MOTOR GRADER, WHEEL LOADER,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
$10.72
22 Aug 2023
US: Florida-Parts-Z
1M7821 - Gasket fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$10.59
09 May 2022
0.5952[0.27] Pounds
US: ProperBuy
6N4985 Gasket Radiator Fits Caterpillar 1M7821
TCP Warranty
TCP Warranty
Number on catalog scheme:
12
For full view, you need register
Compatible equipment models: 1M7821:
Caterpillar parts catalog:
Information:
Remove Oil Pump (3304)
START BY:a. remove oil pan 1. Remove bolts (3) that hold the elbow to the oil pump.
Oil pump idler gear (2) can fall off the oil pump when the oil pump is removed. To prevent injury, always hold the gear on the oil pump when it is removed from the engine.
2. Remove the bolts, locks and washers that hold oil pump (1) to the engine. Remove the oil pump from the engine.Install Oil Pump (3304)
1. Turn the crankshaft until the No. 1 piston is at top center of the compression stroke. See Testing And Adjusting for this procedure.2. Turn both balancer shafts (1) until the flat part of the shaft is away from the oil pan plate. Install bolts (3) [3/8"-16 NC x 51 mm (2 in.) long] through the holes in the oil pan plate and into the threaded holes in the balancer shafts.3. Install idler gear (2) on the oil pump. Put oil pump (5) in position on the engine as shown. Make sure the oil pump gears are engaged with the balancer shaft gears and the crankshaft gear. Install the bolts, washer and locks that hold the oil pump in position.4. Install bolts (4) that hold the elbow to the oil pump.5. Remove bolts (3) from the balancer shafts. Remove the timing bolt from the flywheel.END BY:a. install oil pan
START BY:a. remove oil pan 1. Remove bolts (3) that hold the elbow to the oil pump.
Oil pump idler gear (2) can fall off the oil pump when the oil pump is removed. To prevent injury, always hold the gear on the oil pump when it is removed from the engine.
2. Remove the bolts, locks and washers that hold oil pump (1) to the engine. Remove the oil pump from the engine.Install Oil Pump (3304)
1. Turn the crankshaft until the No. 1 piston is at top center of the compression stroke. See Testing And Adjusting for this procedure.2. Turn both balancer shafts (1) until the flat part of the shaft is away from the oil pan plate. Install bolts (3) [3/8"-16 NC x 51 mm (2 in.) long] through the holes in the oil pan plate and into the threaded holes in the balancer shafts.3. Install idler gear (2) on the oil pump. Put oil pump (5) in position on the engine as shown. Make sure the oil pump gears are engaged with the balancer shaft gears and the crankshaft gear. Install the bolts, washer and locks that hold the oil pump in position.4. Install bolts (4) that hold the elbow to the oil pump.5. Remove bolts (3) from the balancer shafts. Remove the timing bolt from the flywheel.END BY:a. install oil pan
Parts gasket Caterpillar catalog:
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
140B, 14E
120
120, 120B, 12E, 140, 140B
12F, 14E, 16
12E
120B, 12E, 140B, 16
12E
613, D9G
3D7051
GASKET
657, 657B, 666
657, 657B, 666
3D2354
GASKET
657, 657B, 666
657, 657B, 666
4D6952
GASKET
657, 657B, 666
657, 657B, 666
3L6671
GASKET
631C, 824B, 834
631C, 824B, 834
627, 627B, 637, 637B, 637D, 639D
621, 980
1S9136
GASKET
621, 980
621, 980
2S5158
GASKET
621, 980
621, 980
621, 623, 980, D10
140B, 14E, 518, 528, 528B, 530B, 613B, 910, 920, 930, 950
120, 12E, 12F, 140, 14E, 920, 930