1S3524 GASKET KIT-SUP Caterpillar parts
Rating:
Alternative (cross code) number:
CA1S3524
1S-3524
1S3524
CA1S3524
1S-3524
1S3524
Weight: 0.50 pounds 0 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$69.07
14 Jun 2024
0.09[0.04] Pounds
Amazon.com
WVE by NTK 1S3524 Door Lock Switch, 1 Pack
WVE by NTK Power door lock switch controls the current flow to the door lock actuators || When not replaced, door locks will not function or stay on continually and/or cause pre-mature door lock failure || Designed to meet or exceed OE specifications in form, fit and function || Global coverage for import and/or domestic applications
WVE by NTK Power door lock switch controls the current flow to the door lock actuators || When not replaced, door locks will not function or stay on continually and/or cause pre-mature door lock failure || Designed to meet or exceed OE specifications in form, fit and function || Global coverage for import and/or domestic applications
Information:
Table 1
Diagnostic Trouble Codes    
J1939 Code    CDL Code    Code Description    Comments    
3511-11     3482-11     Sensor Supply #3:Other Failure Mode     High or low battery voltage supply has been detected on the 5V supply to the DEF pump.    
Follow the troubleshooting procedure in order to identify the root cause of the problem.    Note: 372-5260 Test Kit is required for completing this procedure.
Illustration 1 g03196836
Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps    Values    Results    
1. Check the DEF Pump Pressure Sensor Supply Circuit for Excessive Voltage
A. Turn the keyswitch to the OFF position for 2 minutes. The keyswitch must be OFF for 2 minutes to allow the DEF pump to purge, reset the code, and reset the Diesel Exhaust Fluid Controller (DCU).
B. Disconnect the Pump Electronic Tank Unit (PETU) harness from the DEF pump.
C. Verify that the harness connector is free of debris, free of corrosion, and securely connected.
D. Turn the keyswitch ON.
E. Measure the voltage between the 5V SUPPLY (Terminal 2) at the DEF pump connector and a known good ground source.
   
Supply Voltage    
Result: The voltage is greater than 5V.
Proceed to Test Step 3.
Result: The voltage is 5V or less.
Proceed to Test Step 2.
   
2. Check the DEF Pump Pressure Sensor Supply for a Short Circuit to Ground
A. Turn the keyswitch to the OFF position for 2 minutes. The keyswitch must be OFF for 2 minutes to allow the DEF pump to purge, reset the code, and reset the DCU.
B. Disconnect the PETU wiring harness from the DEF pump.
C. Disconnect the 86 pin connector from the DCU.
D. Connect the 398-5056 Break-out Connector to the DEF pump connector.
The 398-5056 Break-out Connector must be used to prevent damage to the DEF pump connector.
E. Measure the resistance between the 5V SUPPLY (Terminal 2 at the DEF pump connector) and a known good ground source.
   
Short Circuit    
Result: There was more than 100K ohms of resistance between the
Parts gasket Caterpillar catalog:
1S1749
GASKET
Caterpillar
Caterpillar
1S1340
GASKET KIT
Caterpillar
Caterpillar
1S1339
GASKET KIT
Caterpillar
Caterpillar
1S1338
GASKET KIT
Caterpillar
Caterpillar
1S1337
GASKET KIT
Caterpillar
Caterpillar
1S1336
GASKET KIT
Caterpillar
Caterpillar
1S3530
GASKET KIT-SUP
Caterpillar
Caterpillar
1S3529
GASKET KIT-SUP
Caterpillar
Caterpillar
1S3528
GASKET KIT-SUP
Caterpillar
Caterpillar
1S3527
GASKET KIT-SUP
Caterpillar
Caterpillar
1S3526
GASKET KIT-SUP
Caterpillar
Caterpillar
1S3525
GASKET KIT-SUP
Caterpillar
Caterpillar