2D8157 GASKET Caterpillar parts
120, 120B, 12E, 140, 140B, 14E
Rating:
Alternative (cross code) number:
CA2D8157
2D-8157
2D8157
CA2D8157
2D-8157
2D8157
Weight: 0.19 pounds 0 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement Parts for Snow Removal UTV ATV Cart Machinery for Caterpillar Gasket 2D8157 Model-DFC589-Gl85080
Generic Reliable replacement parts for a range of equipment: lawn and garden, snow removal, UTV, ATV, and golf carts || High-grade materials ensure durability and functionality, even under tough conditions || User-friendly installation for quick, efficient maintenance on essential equipment || Enhances overall performance and lifespan of machinery, minimizing downtime || Suitable for numerous brands, allowing a versatile approach to machinery upkeep
Generic Reliable replacement parts for a range of equipment: lawn and garden, snow removal, UTV, ATV, and golf carts || High-grade materials ensure durability and functionality, even under tough conditions || User-friendly installation for quick, efficient maintenance on essential equipment || Enhances overall performance and lifespan of machinery, minimizing downtime || Suitable for numerous brands, allowing a versatile approach to machinery upkeep
Number on catalog scheme:
None
For full view, you need register
Information:
Probable Causes
Active codes and logged codes
Excessive idle or high load
Fuel quality
Fuel system
Engine speed/timing
Fuel injection system
Air inlet and exhaust
Check for damaged accessory equipmentRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active diagnostic codes. Specifically check for codes related to the fuel system, air inlet and exhaust , and speed timing.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
Codes
Result: A code is active or logged.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. Excessive Idle or High Load
A. Use Cat ET to check the Current Totals for excessive idle time and/or for a high load factor. These factors would be indicative of poor operating habits.
Idle Time or Load
Result: The idle times or load was excessive.
Reduce idle times or load.
Verify that the repair eliminated the problem.
Result: The idle times or load was not excessive.
Proceed to Test Step 3.
3. Check the Fuel Quality
A. The grade of the fuel affects the rate of fuel consumption. Refer to the engines Operation and Maintenance Manual for additional information.
Cold weather adversely affects the characteristics of the fuel. Monitor the status screen on Cat ET in order to verify that the engine has exited cold mode (if applicable). Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
Fuel Quality
Result: The fuel quality meets specifications.
Proceed to Test Step 4.
Result: The fuel quality does not meet specifications.
Repair: Replace the fuel with fuel that meets specifications.
Verify that the repair eliminated the problem.
4. Inspect the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Check for the proper operation of the fuel transfer pump.
Fuel system
Result: The fuel system is OK.
Proceed to Test Step 5.
Result: The fuel system is NOT OK.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
5. Calibration Procedure of the Engine Speed/Timing
A. Perform a speed/timing sensor calibration. Refer to the calibration procedure Troubleshooting, "Timing - Calibrate".
Calibration
Result: The speed timing calibration was performed.
Proceed to Test Step 6.
6. Test the Fuel Injectors
A. Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and the injector connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
C. Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid - Test".
Fuel Injector
Result: The tests completed successfully.
Proceed to Test Step 7.
Result: The tests did not complete successfully.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
7. Restriction in the Air Inlet and
Active codes and logged codes
Excessive idle or high load
Fuel quality
Fuel system
Engine speed/timing
Fuel injection system
Air inlet and exhaust
Check for damaged accessory equipmentRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active diagnostic codes. Specifically check for codes related to the fuel system, air inlet and exhaust , and speed timing.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
Codes
Result: A code is active or logged.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. Excessive Idle or High Load
A. Use Cat ET to check the Current Totals for excessive idle time and/or for a high load factor. These factors would be indicative of poor operating habits.
Idle Time or Load
Result: The idle times or load was excessive.
Reduce idle times or load.
Verify that the repair eliminated the problem.
Result: The idle times or load was not excessive.
Proceed to Test Step 3.
3. Check the Fuel Quality
A. The grade of the fuel affects the rate of fuel consumption. Refer to the engines Operation and Maintenance Manual for additional information.
Cold weather adversely affects the characteristics of the fuel. Monitor the status screen on Cat ET in order to verify that the engine has exited cold mode (if applicable). Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
Fuel Quality
Result: The fuel quality meets specifications.
Proceed to Test Step 4.
Result: The fuel quality does not meet specifications.
Repair: Replace the fuel with fuel that meets specifications.
Verify that the repair eliminated the problem.
4. Inspect the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Check for the proper operation of the fuel transfer pump.
Fuel system
Result: The fuel system is OK.
Proceed to Test Step 5.
Result: The fuel system is NOT OK.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
5. Calibration Procedure of the Engine Speed/Timing
A. Perform a speed/timing sensor calibration. Refer to the calibration procedure Troubleshooting, "Timing - Calibrate".
Calibration
Result: The speed timing calibration was performed.
Proceed to Test Step 6.
6. Test the Fuel Injectors
A. Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and the injector connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
C. Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid - Test".
Fuel Injector
Result: The tests completed successfully.
Proceed to Test Step 7.
Result: The tests did not complete successfully.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
7. Restriction in the Air Inlet and
Caterpillar parts catalog:
Parts gasket Caterpillar catalog:
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
140B, 14E
120
120, 120B, 12E, 140, 140B
12F, 14E, 16
140B
12E
120B, 12E, 140B, 16
12E
120B, 12E, 140, 140B
120B, 12E, 140, 140B
120B, 12E, 140, 140B, 14E
120B, 12E, 140, 140B, 14E
5D4975
GASKET
140, 14E
140, 14E
4D2693
GASKET
120B, 12E, 140, 140B, 14E
120B, 12E, 140, 140B, 14E
120, 12E, 12F, 14E
120, 120B, 12E, 12F, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
120, 120B, 12E, 140, 14E