4N1848 GASKET Caterpillar parts
3408, 3408B, 3408C, 3408E, 3412, 3412C, 589, 631D, 631E, 631G, 633D, 633E II, 637D, 637E, 637G, 657E, 69D, 769C, 769D, 771C, 771D, 834B, 836, 988B, 988F, 988F II, AD40, AD45, AE40, AE40 II, CG137-08, ...
Rating:
Alternative (cross code) number:
CA4N1848
4N-1848
4N1848
CA4N1848
4N-1848
4N1848
Weight: 0.04 pounds 0 kg.
COLD PLANER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$11.90
07 Aug 2023
0.11[0.05] Pounds
KW: GHR SPARES PART
4N1848 Gasket Fits Caterpillar
TCP Warranty
TCP Warranty
$14.50
03 Jul 2022
US: # 1 Quality Par
Aftermarket replacement 4N1848 Cat Gasket
Generic P008429, 4N1848, M-4N1848, 4N1848, Cat Gasket, Cat, Gasket 4N1848, Cat
Generic P008429, 4N1848, M-4N1848, 4N1848, Cat Gasket, Cat, Gasket 4N1848, Cat
This part in 2 request:
Show.
This information for suppliers only!
2023-07-18
2021-11-05
Compatible equipment models: 4N1848:
Information:
Disassemble the Starting Motor
Note: The disassembly and assembly that follows is of the 24 volt starting motor. The 12 volt is similar.
Table 1
Required Tools    
Tool    Part Number    Part Description    Quantity    
A     1P-1855     Retaining Ring Pliers     1    
B     1P-0510     Driver Gp     1    
Illustration 1 g00810559
Disconnect wire assembly (4) from solenoid (1). Disconnect motor terminal connector (3) from the starting motor housing.
Remove three bolts (2) from the shift lever housing. Do not disassemble the solenoid. The parts inside the solenoid are not serviceable.
Illustration 2 g00818016
Remove the O-ring seal and bushing (5) .
Illustration 3 g00810580
Remove the nut (6). Remove the solenoid from the shift lever housing.
Illustration 4 g00810574
Remove the negative terminal nuts "-", wire assembly (2), and washers. Remove six bolts (8) and rear housing (7) .
Illustration 5 g00818558
If necessary, remove bushing (9) from the rear housing.
Illustration 6 g00810576
Remove washer (12) from the armature shaft. Lift brush springs (10) and pull the brushes away from the commutator. Position the brush springs (10) on the side of the brushes in order to hold the brushes in the holders.
Disconnect field winding leads (13) from brush holder (11). Remove the brush holder.
Illustration 7 g00818538
Remove brushes (15) and negative "-" terminal (14) from the brush holders.
Illustration 8 g00810579
Scribe a line on the pinion drive, the shift lever and the starting motor housings for the correct alignment at assembly.
Remove six bolts (17) and pinion drive housing (16) .
Illustration 9 g00810582
Remove retainer (18) with tool (A). Remove shift lever pin (20). If necessary, remove the O-ring seals from the shift lever pin.
Remove pinion drive (19) and the shift lever.
Illustration 10 g00810585
Remove the brake disc from the armature shaft. Remove five bolts (22), shift lever housing (21) and the washer. If necessary, remove the outside O-ring seals.
If necessary, remove the seal and the bushing from the shift lever housing.
Illustration 11 g00810588
Remove armature (22) from the starting motor housing.
Illustration 12 g00810589
Remove the following components from the starting motor housing: eight screws (26), pole shoes (25) and field winding coil (24). It may be necessary to use an impact driver to remove screws (26) .
Clean the armature, field winding coil and pinion drive with mineral spirits and a brush.Note: If the commutator is dirty, the commutator may be cleaned with Number 00 sandpaper. Do not use emery cloth.
Inspect all parts for wear and damage.
Note: The disassembly and assembly that follows is of the 24 volt starting motor. The 12 volt is similar.
Table 1
Required Tools    
Tool    Part Number    Part Description    Quantity    
A     1P-1855     Retaining Ring Pliers     1    
B     1P-0510     Driver Gp     1    
Illustration 1 g00810559
Disconnect wire assembly (4) from solenoid (1). Disconnect motor terminal connector (3) from the starting motor housing.
Remove three bolts (2) from the shift lever housing. Do not disassemble the solenoid. The parts inside the solenoid are not serviceable.
Illustration 2 g00818016
Remove the O-ring seal and bushing (5) .
Illustration 3 g00810580
Remove the nut (6). Remove the solenoid from the shift lever housing.
Illustration 4 g00810574
Remove the negative terminal nuts "-", wire assembly (2), and washers. Remove six bolts (8) and rear housing (7) .
Illustration 5 g00818558
If necessary, remove bushing (9) from the rear housing.
Illustration 6 g00810576
Remove washer (12) from the armature shaft. Lift brush springs (10) and pull the brushes away from the commutator. Position the brush springs (10) on the side of the brushes in order to hold the brushes in the holders.
Disconnect field winding leads (13) from brush holder (11). Remove the brush holder.
Illustration 7 g00818538
Remove brushes (15) and negative "-" terminal (14) from the brush holders.
Illustration 8 g00810579
Scribe a line on the pinion drive, the shift lever and the starting motor housings for the correct alignment at assembly.
Remove six bolts (17) and pinion drive housing (16) .
Illustration 9 g00810582
Remove retainer (18) with tool (A). Remove shift lever pin (20). If necessary, remove the O-ring seals from the shift lever pin.
Remove pinion drive (19) and the shift lever.
Illustration 10 g00810585
Remove the brake disc from the armature shaft. Remove five bolts (22), shift lever housing (21) and the washer. If necessary, remove the outside O-ring seals.
If necessary, remove the seal and the bushing from the shift lever housing.
Illustration 11 g00810588
Remove armature (22) from the starting motor housing.
Illustration 12 g00810589
Remove the following components from the starting motor housing: eight screws (26), pole shoes (25) and field winding coil (24). It may be necessary to use an impact driver to remove screws (26) .
Clean the armature, field winding coil and pinion drive with mineral spirits and a brush.Note: If the commutator is dirty, the commutator may be cleaned with Number 00 sandpaper. Do not use emery cloth.
Inspect all parts for wear and damage.
Cat SIS web machinery list:
Parts gasket Caterpillar catalog:
1T1222
GASKET
24H, 24M, 69D, 769C, 769D, 771C, 771D, 773B, 773D, 773E, 773F, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G LRC, 775G OEM, 988F II, D350E, D350E II, D35HP, D400, D400E, D400E II, D40D
24H, 24M, 69D, 769C, 769D, 771C, 771D, 773B, 773D, 773E, 773F, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G LRC, 775G OEM, 988F II, D350E, D350E II, D35HP, D400, D400E, D400E II, D40D
9D8224
GASKET
769C, 772B, 773B, 775B
769C, 772B, 773B, 775B
1174090
GASKET
69D, 769D, 771D, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
69D, 769D, 771D, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
1139558
GASKET
69D, 769D, 770, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777G
69D, 769D, 770, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777G
1453188
GASKET
69D, 769D, 771D, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777G
69D, 769D, 771D, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777G
3P3729
GASKET
769C, 773B, 776, 777
769C, 773B, 776, 777
3P3719
GASKET
768C, 769C, 773B, 776, 777
768C, 769C, 773B, 776, 777
3P8188
GASKET
769C
769C
1143824
GASKET
D10N, D10R, D10T, D11R, D11T, D8L, D9N, D9R
D10N, D10R, D10T, D11R, D11T, D8L, D9N, D9R
1088105
GASKET
D10N, D10R, D8L, D9N, D9R
D10N, D10R, D8L, D9N, D9R
7N4251
GASKET
D8L
D8L
6E5613
GASKET
D9R
D9R
4N5795
GASKET
3408, 3408B, 3408C, 3408E, 589, 631D, 631E, 633D, 633E II, 637D, 637E, 657E, 69D, 769C, 769D, 771C, 771D, 834B, 836, 988B, 988F, 988F II, AD40, AD45, AE40, AE40 II, D8L, D9N, D9R, PM-565, PM-565B, PR-...
3408, 3408B, 3408C, 3408E, 589, 631D, 631E, 633D, 633E II, 637D, 637E, 657E, 69D, 769C, 769D, 771C, 771D, 834B, 836, 988B, 988F, 988F II, AD40, AD45, AE40, AE40 II, D8L, D9N, D9R, PM-565, PM-565B, PR-...
4N0964
GASKET
3408
3408
3H1952
GASKET
3408, 3408B, 3408C, D326F, D337, D342, D342C, D353C, D375D, D397D, D8H
3408, 3408B, 3408C, D326F, D337, D342, D342C, D353C, D375D, D397D, D8H
6I1778
GASKET
3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, C30, C32
3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, C30, C32
7E7308
GASKET-CYLINDER HEAD
3408, 3408B, 3408C, 589, 631E, 637E, 657E, 769C, 771C, 834B, 836, 988B, 988F, AD40, AE40, D9N, D9R, G3408, G3408B, G3408C, PM-565, PR-450, PR-450C
3408, 3408B, 3408C, 589, 631E, 637E, 657E, 769C, 771C, 834B, 836, 988B, 988F, AD40, AE40, D9N, D9R, G3408, G3408B, G3408C, PM-565, PR-450, PR-450C
2W7984
GASKET-CYLINDER HEAD
3408, 637D, 657E, 988B, D8L, PR-450
3408, 637D, 657E, 988B, D8L, PR-450
7N7442
GASKET
14G, 14H NA, 16G, 16H NA, 3176, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 3406B, 3406C, 3406E, 3508, 3508B, 3512, 3512B, 3516, 3516B, 611, 615C, 621, 621E, 621F, 621R, 623E, 623F, 627E, 627F, 814B...
14G, 14H NA, 16G, 16H NA, 3176, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 3406B, 3406C, 3406E, 3508, 3508B, 3512, 3512B, 3516, 3516B, 611, 615C, 621, 621E, 621F, 621R, 623E, 623F, 627E, 627F, 814B...
3886565
GASKET-CYLINDER HEAD
3408, 3408C
3408, 3408C
3982959
GASKET-PLATE
3408, 3408C
3408, 3408C
5N5276
GASKET
3406, 3406B, 3408
3406, 3406B, 3408
9G6421
GASKET
3406, 3406B, 3408
3406, 3406B, 3408
1115822
GASKET-EXHAUST
3408, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, C175-16, C280-12, C280-16, C280-6, C280-8, C32, G3512B, G3516, G3516B, G3516C, G3516E, G3516H, G3520B, G3520C,...
3408, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, C175-16, C280-12, C280-16, C280-6, C280-8, C32, G3512B, G3516, G3516B, G3516C, G3516E, G3516H, G3520B, G3520C,...