GASKET 4W9653 - Caterpillar

System configuration parameters are parameters that affect emissions and power of the engine. Default values for the parameters are programmed at the factory. Some parameters may be changed by the customer in order to suit the needs of the specific application. Values for these parameters can be viewed on the electronic service tool. Certain configuration parameters are also stamped on the engine information plate.No password is required for programming a new Electronic Control Module (ECM) during the first 100 hours of service life. This 100 hour “free configuration” feature enables the customer to tailor the programmable setpoints to the requirements of the installation. Exceptions are "Fuel Limit" and "Personality Module Mismatch".Note: If the parameters that are protected with the factory passwords are changed, the Caterpillar warranty may be voided.
Table 1
System Configuration Parameters
Parameter Default Range Password
Required
Personality Module Interlock Yes
ECM
Serial Number Yes
Engine Serial Number 00000000 8 alphanumeric numbers No
Equipment ID 00000000000000000 17 alphanumeric numbers No
Full Load Setting (FLS) 0 -128 to +127 Yes
Full Torque Setting (FTS) 0 -128 to +127 Yes
"Fuel Ratio Control Offset (FRC)" 0 −25 to 0 No
"Rated Fuel Positon (mm)" 14 The minimum rack is based on engine power. Yes
Fuel Correction Factor (%) 0 -25 to +25 No
Low Idle (rpm) 1000 810 to 1000 No
Droop (%) 0.0 0.0 to 10.0 No
"Governor Gain Factor" Engine rating 0 to 39,999 Yes
"Governor Minimum Stability Factor" Engine rating 0 to 39,999 Yes
"Governor Maximum Stability Factor" Engine rating 0 to 39,999 Yes
Acceleration delay on start-up (sec) 0 0 to 60 No
Acceleration Rate (rpm/sec) 250 5 to 2000 No
Programmable Torque Scaling The minimum rack is based on engine power. The minimum rack is based on engine power. Yes
"Engine Cooling System Configuration" SCAC SCAC or JWAC Yes
Cold Cylinder Cutout Disabled Enabled
Disabled No
"Cooldown Engine Speed (rpm)" 900 810 to 1800 No
"Engine Cooldown Duration (min)" 0 0 to 30 No
"Engine Prelube Duration (sec)" 0 0 to 210 No
"Crank Duration (sec)" 0 0 to 60 No
"Maximum Number of Crank Cycles" 0 0 to 10 No
"Crank Terminate Speed (rpm)" 400 100 to 500 No
"Total Tattletale" 0 0 to 255 N/A
Injector Code (1) 0000 4 numbers No
Injector Code (2) 0000 4 numbers No
Injector Code (3) 0000 4 numbers No
Injector Code (4) 0000 4 numbers No
Injector Code (5) 0000 4 numbers No
Injector Code (6) 0000 4 numbers No
Injector Code (7) 0000 4 numbers No
Injector Code (8) 0000 4 numbers No
Injector Code (9) 0000 4 numbers No
Injector Code (10) 0000 4 numbers No
Injector Code (11) 0000 4 numbers No
Injector Code (12) 0000 4 numbers No
Injector Code (13) 0000 4 numbers No
Injector Code (14) 0000 4 numbers No
Injector Code (15) 0000 4 numbers No
Injector Code (16) 0000 4 numbers No Parameter Descriptions
"Personality Module Interlock"
The "Personality Module Interlock" is automatically programmed by the ECM after factory passwords are entered."ECM Serial Number"
The "ECM Serial Number" is stored in the memory of the ECM. The "ECM Serial Number" can be accessed by the use of the service tool."Engine Serial Number"
Program the "Engine Serial Number" to match the engine serial number that