GASKET KIT- 6V2546 - Caterpillar

6V2546 GASKET KIT- Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA6V2546
6V-2546
6V2546

Weight: 0.48 pounds 0 kg.

Buy GASKET KIT- 6V2546 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:

6V2546 GASKET KT-YM 4373203 CL

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

6V2546 | Caterpillar Gasket Set - Fuel System

$163.37

29 Sep 2021
0.75[0.34] Pounds
US: Highway And Hea

6V2546 | Caterpillar Gasket Set - Fuel System
HHP HIGHWAY & HEAVY PARTS HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Image(s) is for illustration purposes only and may not represent the actual part. || Products are only sourced from quality certified manufacturing facilities.

$65.13

17 Jun 2021
0.5070[0.23] Pounds
US: IronDT

6V2546 Gasket Set Fits Caterpillar
TCP Warranty

Show more prices Caterpillar parts

For full view, you need register

Information:

Illustration 1 g00678674
Schematic of the SPI Data Link
This diagnostic code is recorded when the VIMS electronic control module determines that information on the SPI data link is erratic or the data makes no sense.System Response:When this diagnostic code is present the following conditions may be present:
Any of the display modules or all of the display modules may not work during operation or the display modules during the self test.
Any of the display modules of the display modules or all of the display modules may be erratic during operation of the machine or the display modules during the self test.Test Step 1. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect the harness connections that are related to the SPI data link. Make sure that the connectors are clean and tight.
Check the mating of the harness connectors.
Check wires at the connector.
Check each wire for nicks or signs of abrasion in the insulation.
Check for moisture at the connector.
Check for dirty contacts or corroded contacts.
Check each pin and each socket. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 2.
NOT OK - The machine harness connectors are NOT tight and free of corrosion. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK FOR A SHORT TO +BATTERY.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1and J2 connectors from the ECM.
Disconnect the machine harness connectors from all of the display modules.
At the J1and J2 machine harness connectors for the ECM, measure the resistance between the contacts that are listed below:
Connector contact J1-1(wire 170-YL(Yellow)) and the SPI Data Link circuit contact J2-10 (wire C413-YL(Yellow)).
Connector contact J1-1 (wire 170-YL(Yellow)) and the SPI Data Link circuit contact J2-20 (wire C414-BU(Blue)).
Connector contact J1-1 (wire 170-YL(Yellow)) and the SPI Data Link circuit contact J2-28 (wire E708-PK(Pink)). Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. Proceed to test step 3.
NOT OK - The resistance is less than 5 ohms. The machine harness has failed.Repair: There is a short between the +battery and the circuits of the SPI data link in the machine harness. Replace the machine harness or repair the machine harness.STOPTest Step 3. CHECK FOR AN OPEN HARNESS.
The disconnect switch and the key start switch remain in the OFF position.
All the display modules remain disconnected from the machine harness.
Measure the resistance of the circuits of the SPI data link that are listed below:
Measure the resistance between connector contact J2-10 (wire C413-YL(Yellow)) to connector contact 4 (wire C413-YL(Yellow)) of the message center module.
Measure the resistance between connector contact J2-20 (wire C414-BU(Blue)) to connector contact 5 (wire C414-BU(Blue)) of the message center module.
Measure the resistance between connector contact J2-28 (wire E708-PK(Pink)) to connector contact 3 (wire E708-PK(Pink)) of the message center module.Expected Result:The resistance is less than 5 ohms. Results:
OK - The resistance is less than 5 ohms. The circuit resistance is