GASKET KT-V G 6V9250 - Caterpillar

6V9250 GASKET KT-V G Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA6V9250
6V-9250
6V9250

Weight: 10 pounds 4 kg.

Buy GASKET KT-V G 6V9250 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$389.00

03 Jul 2022

CN: kangpinyouxuan

Head Gasket Set 6V9250 for Caterpillar
N\\C Part Number: 6V9250 || Applicable Models: for Caterpillar || Warranty: 1 Year. || TIPS: Please be sure to compare carefully with photos and check part number before buying items, If you are not sure this part is suitable, please feel free to contact us, we'll reply you as soon as possible. || Delivery Time: We will ship the item to you by DHL/FedEx/USPS, which will arrive in 5-9 days once we ship it to you. The delivery time will not a month like which shown online, you could buy with confidence!

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#818751 6v-9250

2022-03-01

For full view, you need register

Information:

Illustration 5 g00914693
Remove timing pin (16) from the storage position on the side of the engine.
Turn the camshaft until timing pin (16) can be installed through the cylinder block and into groove (17) that is in the camshaft.
Repeat Steps 14 and 15 for the camshaft on the opposite side of the engine.
Illustration 6 g00914707
Remove bolts (19), cover (18), and plug (20).
Illustration 7 g00930884
Install one bolt (19) into the flywheel housing through the hole for plug (20). Use Tooling (E) and a ratchet to turn the flywheel until bolt (19) can be installed through the hole and into the flywheel. This will position the No. 1 cylinder at the top center. Refer to the Service Manual, "Systems Operation/Testing and Adjusting" for more information.
Illustration 8 g00914726
Place camshaft drive gears (8) into position on both of the camshafts.
Illustration 9 g00914728
Install timing ring (11) and the bolt on the camshaft that is on the left side of the engine. Ensure that the hole in the timing ring is properly seated on the locating pin.
Illustration 10 g00914730
Install plate (7) and the bolt on the camshaft that is on the right side of the engine.
Use the following steps to seat camshaft drive gears (8) onto the ends of the camshafts.
Tighten the bolt for timing ring (11) to a torque of 360 40 N m (266 30 lb ft).
Place an index mark on the bolt for timing ring (11).
Place a driver against the retaining plate of the camsaft drive gear (8) Strike the driver solidly with a hammer 3 to 4 times. This will help seat camshaft drive gear (8) on the camshaft.
Tighten the bolt for timing ring (11) again to a torque of 360 40 N m (266 30 lb ft).
Repeat Steps 22.c and 22.d until the bolt for timing ring (11) turns a minimum of 90 degrees.
Repeat Steps 22.a through 22.e in order to seat camshaft drive gear (8) on the opposite side of the engine.
Illustration 11 g00914693
Remove the timing pins from the camshafts (17). Install the timing pins in original locations (16).
Illustration 12 g00914380
Install the gaskets and two covers (6) over the camshaft drive gears on both sides of the engine.
Illustration 13 g00930884
Illustration 14 g00914707
Remove bolt (19) from the flywheel. Install plug (20) in the timing hole. Remove Tooling (E) and install cover (18) with bolts (19) on the flywheel housing.
Illustration 15 g00914348
Install two covers (4) on the front housing.
Illustration 16 g00928893
Remove the O-ring seals from valve lifters (5). Push the valve lifters against the camshaft.
Illustration 17 g00914320
Install access covers (2) and tube assemblies (1) on both sides of the engine. End By:
Install the speed/timing sensor. Refer to the Service Manual, "Electronic Troubleshooting" module.
Install the rocker shaft assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Push Rods - Install".