7E3772 GASKET Caterpillar parts
3508, 3508B, 3508C, 3512, 3516, 3516B, 5130, 5230, 5230B, 776C, 777D, 784B, 785, 785B, 785D, 789B, 789C, 793, 793B, 797B, 994, 994D, D11N, D11R, G3508, G3508B, G3512, G3512B, G3516, G3516B, G3520B, PM...
Rating:
Alternative (cross code) number:
CA7E3772
7E-3772
7E3772
CA7E3772
7E-3772
7E3772
Weight: 0.05 pounds 0 kg.
GAS ENGINE, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
7E3772 GASKET VALVE COVER Suitable For Caterpillar 7E3772
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
7E3772 GASKET VALVE COVER Suitable For Caterpillar® 7E3772
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
This part in 4 request:
Show.
This information for suppliers only!
2023-11-29
2022-12-27
2021-05-11
2019-01-18
Compatible equipment models: 7E3772:
PETROLEUM ENGINE
3512
Information:
Generator Alignment
Note: For the alignment procedure for two-bearing close coupled generators, see Special Instruction, SEHS7073, "Alignment Of Two Bearing Generators". Note: A specific alignment procedure is not required for generators that are soft mounted.Align Generator Sets With No Supports At The Flywheel Housing
Illustration 1 g00854158
Generator Set With No Support At The Flywheel Housing (1) Bolts (2) Base
If the base (2) of the generator set is fastened to a foundation, loosen all the bolts that connect the base to the foundation. Loosen all bolts that fasten the generator supports and the engine supports to the base (2).
Ensure that there is clearance between the bolts and the bolt holes in the base, the engine supports and the generator supports at all locations.
Check the clearance between the base and the foundation at all mounting locations. Shims should be used in order to prevent the deflection of the base as the bolts that connect the base to the foundation are tightened. When there is no deflection of the base, tighten all bolts that connect the base to the foundation to the final torque.
Illustration 2 g00854145
(3) Long Support (4) Locations of the Supports
Check the clearance between the base (2) and the engine. Check the clearance between the base (2) and the engine supports. Check the clearance between the base and the generator supports (2). Check the clearance over the entire length of the supports. This is especially important on generators with long supports (3), since some of the surfaces may not be square or parallel. Shims should be used in order to prevent the deflection of the supports as the bolts are tightened. After all the necessary shims have been installed, finish tightening all mounting bolts to the final torque. Align Generator Sets With Supports At The Flywheel Housing
Illustration 3 g00854147
Generator Set With Supports At The Flywheel Housing (1) Bolts (2) Support (3) Base
Illustration 4 g00854174
(4) Bolts (5) Shims
If base (3) of the generator set is fastened to a foundation, loosen all bolts that connect the base (3) to the foundation. Loosen all bolts (4) that fasten the engine supports and generator supports to the base.
Ensure that there is enough clearance between the bolts (4) and the bolt holes in the base (3), engine supports and generator supports (2) at all locations.
Check the clearance between the base (3) and the foundation at all mounting locations. Shims should be used in order to prevent the deflection of the base as the bolts that connect the base to the foundation are tightened. When there is no deflection in the base, tighten all bolts that connect the base to the foundation to the final torque.
Illustration 5 g00854148
(6) Bolts
While the generator is supported by a crane, loosen all bolts (6) that fasten the generator to the flywheel housing. Tighten alternate bolts to the final torque.
Check the clearance between the base and the engine and generator supports at all four locations. Check the clearance over the entire length of the supports. This is especially important on generators with long supports. Shims (5)
Note: For the alignment procedure for two-bearing close coupled generators, see Special Instruction, SEHS7073, "Alignment Of Two Bearing Generators". Note: A specific alignment procedure is not required for generators that are soft mounted.Align Generator Sets With No Supports At The Flywheel Housing
Illustration 1 g00854158
Generator Set With No Support At The Flywheel Housing (1) Bolts (2) Base
If the base (2) of the generator set is fastened to a foundation, loosen all the bolts that connect the base to the foundation. Loosen all bolts that fasten the generator supports and the engine supports to the base (2).
Ensure that there is clearance between the bolts and the bolt holes in the base, the engine supports and the generator supports at all locations.
Check the clearance between the base and the foundation at all mounting locations. Shims should be used in order to prevent the deflection of the base as the bolts that connect the base to the foundation are tightened. When there is no deflection of the base, tighten all bolts that connect the base to the foundation to the final torque.
Illustration 2 g00854145
(3) Long Support (4) Locations of the Supports
Check the clearance between the base (2) and the engine. Check the clearance between the base (2) and the engine supports. Check the clearance between the base and the generator supports (2). Check the clearance over the entire length of the supports. This is especially important on generators with long supports (3), since some of the surfaces may not be square or parallel. Shims should be used in order to prevent the deflection of the supports as the bolts are tightened. After all the necessary shims have been installed, finish tightening all mounting bolts to the final torque. Align Generator Sets With Supports At The Flywheel Housing
Illustration 3 g00854147
Generator Set With Supports At The Flywheel Housing (1) Bolts (2) Support (3) Base
Illustration 4 g00854174
(4) Bolts (5) Shims
If base (3) of the generator set is fastened to a foundation, loosen all bolts that connect the base (3) to the foundation. Loosen all bolts (4) that fasten the engine supports and generator supports to the base.
Ensure that there is enough clearance between the bolts (4) and the bolt holes in the base (3), engine supports and generator supports (2) at all locations.
Check the clearance between the base (3) and the foundation at all mounting locations. Shims should be used in order to prevent the deflection of the base as the bolts that connect the base to the foundation are tightened. When there is no deflection in the base, tighten all bolts that connect the base to the foundation to the final torque.
Illustration 5 g00854148
(6) Bolts
While the generator is supported by a crane, loosen all bolts (6) that fasten the generator to the flywheel housing. Tighten alternate bolts to the final torque.
Check the clearance between the base and the engine and generator supports at all four locations. Check the clearance over the entire length of the supports. This is especially important on generators with long supports. Shims (5)
Cat SIS web machinery list:
Parts gasket Caterpillar catalog:
3P0751
GASKET
769C, 769D, 771C, 771D, 773B, 773D, 773E, 775B, 775D, 776, 776C, 776D, 777, 777B, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 994, AD40, AD45, AD45B, AD55, AD55B, ...
769C, 769D, 771C, 771D, 773B, 773D, 773E, 775B, 775D, 776, 776C, 776D, 777, 777B, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 994, AD40, AD45, AD45B, AD55, AD55B, ...
1725718
GASKET
5130, 5130B, 776C, 776D, 777D, 784B, 785B, 785C, 789B, 789C, 793B, 793C, 793D, 797, 797B, 854G, 994
5130, 5130B, 776C, 776D, 777D, 784B, 785B, 785C, 789B, 789C, 793B, 793C, 793D, 797, 797B, 854G, 994
8E7249
GASKET
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992D, 992G, 992K, 993K, D11R, D11T
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992D, 992G, 992K, 993K, D11R, D11T
4W9839
GASKET
776C, 776D, 777, 777B, 777C, 777D, 854G, 992G
776C, 776D, 777, 777B, 777C, 777D, 854G, 992G
1T1925
GASKET
776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D, 854G, 854K, 992G, 992K, 993K
776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D, 854G, 854K, 992G, 992K, 993K
1215746
GASKET
793C, 793D, 797, 797B, 994D, D11R
793C, 793D, 797, 797B, 994D, D11R
4J7083
GASKET
824B, 824G, 824G II, 824H, 834, 854G, 854K, 988, 992, AP-1050, D10, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9L
824B, 824G, 824G II, 824H, 834, 854G, 854K, 988, 992, AP-1050, D10, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9L
7W8604
GASKET
776C, 776D, 777, 777B, 777D, 785D
776C, 776D, 777, 777B, 777D, 785D
4F2612
GASKET
776C, 776D, 777, 777B, 777C, 777D
776C, 776D, 777, 777B, 777C, 777D
1008058
GASKET
5130, 776C, D11N, D11R
5130, 776C, D11N, D11R
6I4033
GASKET
784B, 785, 785B
784B, 785, 785B
9G9568
GASKET
784B, 784C, 785, 785B, 785C, 785D, 789, 789B
784B, 784C, 785, 785B, 785C, 785D, 789, 789B
3094550
GASKET
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 797, 797B, G3516H, SPT343, XQC1200, XQC1600
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 797, 797B, G3516H, SPT343, XQC1200, XQC1600
7N3049
GASKET
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 854...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 854...
7J8114
GASKET
215, 215B, 225, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 508, 528, 528B, 530B, 785, 814, 910, 910E, 920, 926, 930, 930R, 931, 931B, 943, 950, 953, 966C, D3, D3B, G3508, G3508B, G351...
215, 215B, 225, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 508, 528, 528B, 530B, 785, 814, 910, 910E, 920, 926, 930, 930R, 931, 931B, 943, 950, 953, 966C, D3, D3B, G3508, G3508B, G351...
7N7308
GASKET
3508, 3508C, 3512, 3512B, 3516, 3606, 3608, 3612, 3616
3508, 3508C, 3512, 3512B, 3516, 3606, 3608, 3612, 3616
7N7307
GASKET
3508, 3508C, 3512, 3512B, 3516
3508, 3508C, 3512, 3512B, 3516
1106991
GASKET-CYLINDER HEAD
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797, 797B, 854...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797, 797B, 854...
9L1480
GASKET
1676, 1693, 3304, 3412, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 621E, 621F, 621G, 623E, 623F, 623G, 627B, 627E, 627F, 627G, D348, D7F, G3508, G3508B, G3512, G3512B, G3512E, G3516, ...
1676, 1693, 3304, 3412, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 621E, 621F, 621G, 623E, 623F, 623G, 627B, 627E, 627F, 627G, D348, D7F, G3508, G3508B, G3512, G3512B, G3512E, G3516, ...
2361655
GASKET-EXHAUST MANIFOLD
3508, 3508B, 3508C, 3512B, 3512C, 3516, 3516B, 3516C, SPF343C, TH48-E80, TH55-E70, XQC1200
3508, 3508B, 3508C, 3512B, 3512C, 3516, 3516B, 3516C, SPF343C, TH48-E80, TH55-E70, XQC1200
2453512
GASKET
3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5230B, 785D, 797B, C15, C18, C18 I6, C27, C32, CX31-C15I, CX35-P800, G3508, G3508B, G3512, G3...
3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5230B, 785D, 797B, C15, C18, C18 I6, C27, C32, CX31-C15I, CX35-P800, G3508, G3508B, G3512, G3...
7N5080
GASKET-MANIFOLD
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D...
7N5089
GASKET
3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C, 5130, 5230, 5230B, 776C, 777B, 777D, 784B, 785, 785B, 785D, 789, 789B, 789C, 793, 793B, 797B, 994, 994D, D11N, D11R, G3508, G3508B, G3512, G3512B, ...
3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C, 5130, 5230, 5230B, 776C, 777B, 777D, 784B, 785, 785B, 785D, 789, 789B, 789C, 793, 793B, 797B, 994, 994D, D11N, D11R, G3508, G3508B, G3512, G3512B, ...
7E4127
GASKET
3508, 3508C, 3512, 3516, 793, G3508, G3512, G3516
3508, 3508C, 3512, 3516, 793, G3508, G3512, G3516