7H3270 GASKET Caterpillar parts
12E, 16, 1673, 1673B, 1673C, 235, 3304, 3306, 518, 594, 621R, 627B, 631C, 637D, 641B, 650B, 657, 657B, 772, 773, 926, 936, 936F, 941, 950, 955H, 955K, 955L, 966C, 966D, 966F, 973, 977H, 977K, 980B, 98...
Rating:
Alternative (cross code) number:
CA7H3270
7H-3270
7H3270
CA7H3270
7H-3270
7H3270
Weight: 0.66 pounds 0 kg.
EXCAVATOR, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$8.08
18 Jan 2024
US: Florida-Parts-Z
7H3270 - Gasket 1S6595 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$5.18
22 Mar 2023
0.01[0.00] Pounds
US: Zbox Global, LL
1S6595 Gasket (P) Fits Caterpillar 7H3270 65C 65D PM-465 816F 826C 826G 836 836G
TCP Warranty
TCP Warranty
$626.86
27 Jul 2022
US: # 1 Quality Par
Aftermarket replacement MCB3406063 Cat 3406/B/C Cylinder Head Gasket Set
Generic MCB3406063, 1006178, 1S4810, 3801564, 1S6595, 3801559, 7H3270, 2N8204, 2N8630, 3E6772, 4W1055, 7C-9912, 4W-1055,
Generic MCB3406063, 1006178, 1S4810, 3801564, 1S6595, 3801559, 7H3270, 2N8204, 2N8630, 3E6772, 4W1055, 7C-9912, 4W-1055,
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 7H3270:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 177-8001 Pilot Sleeve 2
B 249-2936 Adapter 1
C 274-7932(1) or 274-7933(2) Guide 1
(1) Front Removal
(2) Rear RemovalStart By:
Remove the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Care must be used when removing or installing the camshaft. Do not damage the finished surfaces of the camshaft or the camshaft bearings.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01194576
Remove bolts (2) and washers (3).
Remove cover (1) and the O-ring seal.
Illustration 2 g01194581
Remove bolts (4). Remove gear (5).
Illustration 3 g01194585
Remove bolts (6), thrust plate (7), and adapter assembly (8).
Illustration 4 g01194626
Use bolt (6) in order to remove sealing plate (9). Remove the O-ring seals.
Illustration 5 g01194930
Remove bolts (11) and washers (12). Remove cover (10) and the O-ring seal.
Illustration 6 g01194932
Remove bolts (13) and damper (14).
Illustration 7 g01194933
Remove bolts (15). Remove sealing plate (16) and adapter assembly (17).
Illustration 8 g01194934
Install Tooling (A) and Tooling (B) on the rear of camshaft (18). Install Tooling (A) on the front of camshaft (18).
Install Tooling (C) on the front housing or the rear housing. Tooling (C) is used to support the camshaft. Note: It is necessary to install Tooling (A) and Tooling (B) on the camshaft. Tooling (A) and Tooling (B) will support the camshaft as the camshaft is moved out of the cylinder head and into Tooling (C). Align the camshaft with the bore of Tooling (C).Note: Avoid lifting the camshaft. The camshaft should rest on Tooling (A) and Tooling (B). Lifting of the camshaft can cause misalignment as the camshaft is removed, resulting in damage to the camshaft bearings.
Carefully slide the camshaft out of the cylinder head for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 35 kg (77 lb). Note: Rotate the camshaft during removal. This will prevent the camshaft from binding in the camshaft bearings.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 177-8001 Pilot Sleeve 2
B 249-2936 Adapter 1
C 274-7932(1) or 274-7933(2) Guide 1
(1) Front Removal
(2) Rear RemovalStart By:
Remove the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Care must be used when removing or installing the camshaft. Do not damage the finished surfaces of the camshaft or the camshaft bearings.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01194576
Remove bolts (2) and washers (3).
Remove cover (1) and the O-ring seal.
Illustration 2 g01194581
Remove bolts (4). Remove gear (5).
Illustration 3 g01194585
Remove bolts (6), thrust plate (7), and adapter assembly (8).
Illustration 4 g01194626
Use bolt (6) in order to remove sealing plate (9). Remove the O-ring seals.
Illustration 5 g01194930
Remove bolts (11) and washers (12). Remove cover (10) and the O-ring seal.
Illustration 6 g01194932
Remove bolts (13) and damper (14).
Illustration 7 g01194933
Remove bolts (15). Remove sealing plate (16) and adapter assembly (17).
Illustration 8 g01194934
Install Tooling (A) and Tooling (B) on the rear of camshaft (18). Install Tooling (A) on the front of camshaft (18).
Install Tooling (C) on the front housing or the rear housing. Tooling (C) is used to support the camshaft. Note: It is necessary to install Tooling (A) and Tooling (B) on the camshaft. Tooling (A) and Tooling (B) will support the camshaft as the camshaft is moved out of the cylinder head and into Tooling (C). Align the camshaft with the bore of Tooling (C).Note: Avoid lifting the camshaft. The camshaft should rest on Tooling (A) and Tooling (B). Lifting of the camshaft can cause misalignment as the camshaft is removed, resulting in damage to the camshaft bearings.
Carefully slide the camshaft out of the cylinder head for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 35 kg (77 lb). Note: Rotate the camshaft during removal. This will prevent the camshaft from binding in the camshaft bearings.
Cat SIS web machinery list:
Parts gasket Caterpillar catalog:
120B, 12E, 140, 140B
120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
12F, 14E, 16
12E
120B, 12E, 140B, 16
12E
1673C, 3304, 3306, G3306
12F, 14E, 1673C, 3304, 3306, 518, 561C, 627, 637, 815, 920, 930, 941, 950, 951B, 955H, 955K, 955L, 966C, 977K, 980B, D4D, D5, D6C, D7F, D8H, D8K, G3306
12F, 14E, 14G, 1673C, 3304, 3306, 518, 561C, 627, 637, 637D, 815, 920, 941, 950, 951B, 955K, 966C, 977K, 977L, 980B, D4D, D5, D6C, D7F, D7G, G3306
1673C, 3304, 3306, G3306
12E, 1673, 1673B, 215, 225, 3304, 518, 561B, 920, 930, 930R, 941, 950, 950B, 951B, 955H, 955K, 955L, 963, 977H, 977K, D330B, D333A, D333B, D4D, E240, G3304, G3304B
1673, 215, 3304, 3306, D320A, D330A, G3306
1673C, 3304, 3306
3304, 3306
1673C, 215, 3304, 3306, 518, 561C, 621R, 627, 910, 920, 930, 931B, 941, 943, 950, 951B, 953, 955K, 966C, 977K, 977L, 980B, D3, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G, G3306
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 16, 160G, 16G, 16H, 16H NA, 518, 518C, 528, 528B, 530B, 572R, 572R II, 578, 583R, 613B, 631C, 641B, 650B, 657B, 769, 772, 773, 777, 814, 815, 824B, 825B, 910, ...
772, 992, D348, D349
225, 3304, 941, 950, 951B, 955K, D4D