7M1109 GASKET Caterpillar parts
D343
Rating:
Alternative (cross code) number:
CA7M1109
7M-1109
7M1109
CA7M1109
7M-1109
7M1109
Weight: 0.20 pounds 0 kg.
INDUSTRIAL ENGINE,
Compatible equipment models: 7M1109:
Number on catalog scheme:
None
For full view, you need register
Information:
Installation Procedure
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar parts catalog:
Parts gasket Caterpillar catalog:
12E, 12G, 12H, 12H NA, 130G, 140B, 140G, 143H, 14G, 160H, 1673C, 1674, 1676, 1693, 16G, 16H NA, 215, 245, 24H, 24M, 3176B, 3176C, 3196, 3208, 330, 330 FM L, 330 L, 3304, 3306, 3306B, 3306C, 3406, 3406...
120G, 12G, 130G, 140G, 14G, 160G, 16G, 225D, 227, 229D, 235, 245, 3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3412, 3412C, 3456, 508, 518, 518C, 528, 528B, 530B, 561B, 561D, 572G, 578, 5...
16, 16G, 245, 3406, 3406B, 3406C, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 589, 594H, 631C, 631E, 637D, 637E, 651E, 657E, 769, 769C, 771C, 772, 772B, 773B, 775B, 777, 824C, 826C, 834B, 836, 980C, 988B,...
12E, 3304, 3306, 561B, 561C, 621, 641, 651, 657, 666, 769, 824, 951B, 955C, 955K, 977H, 977K, 980, 992, D334, D336, D337F, D342, D342C, D343, D348, D353C, D379A, D398, D4D, D6C, D8H, D9G, G3306, G343
D330A, D330B, D333B, D343
D342, D342C, D343, D353C, G3306, G3406, G343, G3516, G353D
12E, 561B, 583H, 651, 657, 666, 834, 988, D320A, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D379, D397D, D8H, D9E, D9G
D343, D353C, G343
D343, D346, D348, D349, D8K, G343
D343, G343
572G, 583H, 583K, 594, 594H, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 772, 773, 977D, 983, D343, D348, D349, D7F, D7G, D7G2, D8H, D8K, D9G, D9H
D326F, D337, D337F, D342, D343, D353C, D379, D397D, D8H
4L9766
GASKET
D333A
D333A
583K, 657, 657B, D343, D8K
824, 824B, 834, 988, 992, D343
4F5617
GASKET
980, D343
980, D343
3208, 916, CB-614, D4C, D4HTSK II
16, 657, 834, 988, D343
4L6793
GASKET
D320A, D330A
D320A, D330A
5M3583
GASKET
D326F
D326F
7M6044
GASKET
D342C, D343, D353C, D379, D8H, D9G, G342C
D342C, D343, D353C, D379, D8H, D9G, G342C
3406E, 375, 621B, 826C, 980F, 980G, D8N, D8R, D8R II, SS-250
3406B, 375, 826C, 980C, 980F, 980G, D8N, D8R, D8R II, SS-250
D343