GASKET KIT 7X2406 - Caterpillar

7X2406 GASKET KIT Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA7X2406
7X-2406
7X2406

Weight: 1 pounds 0 kg.

Buy GASKET KIT 7X2406 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

7X2406 Gasket KIT/CYL Head (New AFTERMARKET) - G&T Engine Parts

$76.50

10 Jul 2025

US: QUALITY PARTS

7X2406 Gasket KIT/CYL Head (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 2.53 lbs || Dimensions: 10-13.42-29.02 in || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.

$66.46

26 Jul 2022
2.4030[1.08] Pounds
US: TakePart

CTP Caterpillar Kit Gasket (7x2406)
CTP

8T4849 Cylinder Head Gasket Kit 7X2406 fit Caterpillar (CAT) Free Shipping!!!!!

$69.50

22 Apr 2022

US: Florida-Parts-Z

8T4849 Cylinder Head Gasket Kit 7X2406 fit Caterpillar (CAT) Free Shipping!!!!!
FIRST PRICE PARTS

Show more prices Caterpillar parts

For full view, you need register

Information:

Illustration 1 g00732443
Schematic of the load check functionThis diagnostic code is associated with the load check function.FMI 05 is recorded when the transmission electronic control module senses an open in the relay's circuit.Note: The following procedure may cause additional diagnostic codes. Ignore the additional diagnostic codes. Clear the additional diagnostic codes after FMI 05 has been cleared.FMI 05 is present. The load check function is disabled.Test Step 1. CHECK THE RELAY.
Turn the key start switch to the OFF position.
Remove the load check relay.
Measure the resistance from contact 2 to contact 1.Expected Result:The resistance is 300 20 ohms.Results:
YES - The resistance is 300 20 ohms. The relay is functioning properly. Proceed to test step 2.
NO - The resistance is not 300 20 ohms. The relay has failed.Repair: Replace the relay. Stop.Test Step 2. CHECK THE HARNESS.
Clean the relay.
Install the relay.
Verify that the key start switch is in the OFF position.
Disconnect the machine harness from the control module.
Measure the resistance from contact 37 to contact 39 at the machine harness connector.Expected Result:The resistance is 300 20 ohms.Results:
YES - The resistance is 300 20 ohms. The relay is functioning properly. The cause of the problem has not been isolated. Proceed to test step 3.
NO - The resistance is greater than 5000 ohms. The circuit is open. The return wire 571-OR is open or the signal wire 975-WH is open.Repair: Repair the harness or replace the harness. Stop.Test Step 3. VERIFY THAT THE DIAGNOSTIC CODE IS PRESENT.
Verify that the key start switch is in the OFF position.
Inspect the connectors and inspect the contacts.
Connect the machine harness to the control module.
Turn the key start switch to the ON position.
Enter the service mode.
Operate the machine.
Check the diagnostic indicator. Note the active diagnostic codes.Expected Result:The diagnostic code is active.Results:
YES - The diagnostic code is active. The condition has not been corrected. The transmission electronic control module may have failed. Proceed to test step 4.
NO - The diagnostic code is not active. The diagnostic code was caused by a poor electrical connection.Repair: Clear the diagnostic code. Stop.Test Step 4. VERIFY THAT THE TRANSMISSION ELECTRONIC CONTROL MODULE HAS FAILED.
Verify that the key start switch is in the ON position.
Verify that the diagnostic code is present. Verify that the diagnostic code is active.
Turn the key start switch to the OFF position.
Turn the key start switch to the ON position.
Verify that the diagnostic code is present. Verify that the diagnostic code is active.Expected Result:The diagnostic code is active.Results:
YES - The diagnostic code is active. The transmission electronic control module has failed. Repair: Replace the transmission electronic control module. Refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - The diagnostic code is not active. Clear the diagnostic code. Stop.