8F5180 GASKET Caterpillar parts
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
Rating:
Alternative (cross code) number:
CA8F5180
8F-5180
8F5180
CA8F5180
8F-5180
8F5180
Weight: 0.24 pounds 0 kg.
INDUSTRIAL ENGINE, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 8F5180:
Information:
Specifications
Table 1
Dimensions for Acceptable Cylinder Liner Projection with the 362-8264 Cylinder Head Gasket
Part Dimension Value
211-7826 Cylinder Block Liner flange 12.65 0.02 mm (0.498 0.0001 inch) Z
519-7297 Spacer Plate 12.36 0.03 mm (0.4867 0.0012 inch) X
110-6994 Spacer Plate 12.31 0.03 mm (0.4846 0.0012 inch) X
144-5692 Plate Gasket 0.21 0.03 mm (0.008 0.001 inch) Y
Allowable projection 0.05 mm (0.002 inch) to 0.12 mm (0.005 inch) Introduction
Use this procedure to check the cylinder liner projection out of the cylinder block and installed in the cylinder block.Reference: Refer to Reuse And Salvage Guidelines, "Procedure to Salvage Top Decks of Cylinder Blocks of 3500 Engines" for additional information about reuse and/or salvage of the cylinder block.Required Tools
Table 2
Required Tools Qty
1A-0075 Bolt (3/4-16 thread, 44.45 mm (1.750 inch) long) 4
1U-9895 Crossblock 1
3B-1925 Washer (COPPER) 4
3H-0465 Push-Puller Plate 2
6V-7059 Micrometer 1
8F-6123 Bolt (3/4-16 thread, 139.7 mm (5.5.50 inch) long) 2
8T-0455 Liner Projection Tool Group 1 Preparation
For checking the cylinder liner projection with the liner out of the cylinder block, ensure that the following surfaces are clean prior to measuring:
Cylinder liner flanges
Spacer plate
Spacer plate gasketFor checking the installed cylinder liner projection, ensure that the following surfaces are clean prior to measuring:
Top surface of the cylinder block
Cylinder liner bores
Cylinder liner flanges
Spacer plates
Spacer plate gasketCylinder Liner out of the Cylinder Block - Check
Illustration 1 g02247495
Use the 6V-7059 Micrometer to measure the thickness of the following items:
(X) Spacer Plate
(Y) Spacer Plate Gasket
(Z) Cylinder Liner FlangeThe cylinder liner projection depends on which spacer plate is used. Refer to Table 1.Note: To determine the cylinder liner projection, subtract the thickness of the spacer plate and gasket from the thickness of the cylinder liner flange.
Refer to Table 1 for the correct value of your cylinder liner projection based on your spacer plate.Cylinder Liner Installed in the Cylinder Block - Check
Illustration 2 g01192749
Measuring the cylinder liner projection
(1) 3H-0465 Push-Puller Plate
(2) 1P-2403 Dial Indicator
(3) 1P-2402 Gauge Body
(4) 1A-0075 Bolt and 3B-1925 Washer (COPPER)
(5) Spacer plate
(6) 1U-9895 Crossblock
Install a new gasket and spacer plate (5) on the cylinder block.
Install the cylinder liner in the cylinder block without seals or bands.
Hold spacer plate (5) and the cylinder liner in position according to the following procedure:
Install four 3B-1925 Washers (COPPER) and four 1A-0075 Bolts (4) around spacer plate (5). Tighten the bolts evenly to a torque of 95 N m (70 lb ft).
Install the following components: 1U-9895 Crossblock (6), two 3H-0465 Push-Puller Plates (1) and two 8F-6123 Bolts. Ensure that 1U-9895 Crossblock (6) is in position at the center of the cylinder liner. Ensure that the surface of the cylinder liner is clean. Tighten the bolts evenly to a torque of 70 N m (50 lb ft).
Check the distance from the bottom edge of 1U-9895 Crossblock (6) to the top edge of spacer plate (5). The vertical distance from both ends of the
Table 1
Dimensions for Acceptable Cylinder Liner Projection with the 362-8264 Cylinder Head Gasket
Part Dimension Value
211-7826 Cylinder Block Liner flange 12.65 0.02 mm (0.498 0.0001 inch) Z
519-7297 Spacer Plate 12.36 0.03 mm (0.4867 0.0012 inch) X
110-6994 Spacer Plate 12.31 0.03 mm (0.4846 0.0012 inch) X
144-5692 Plate Gasket 0.21 0.03 mm (0.008 0.001 inch) Y
Allowable projection 0.05 mm (0.002 inch) to 0.12 mm (0.005 inch) Introduction
Use this procedure to check the cylinder liner projection out of the cylinder block and installed in the cylinder block.Reference: Refer to Reuse And Salvage Guidelines, "Procedure to Salvage Top Decks of Cylinder Blocks of 3500 Engines" for additional information about reuse and/or salvage of the cylinder block.Required Tools
Table 2
Required Tools Qty
1A-0075 Bolt (3/4-16 thread, 44.45 mm (1.750 inch) long) 4
1U-9895 Crossblock 1
3B-1925 Washer (COPPER) 4
3H-0465 Push-Puller Plate 2
6V-7059 Micrometer 1
8F-6123 Bolt (3/4-16 thread, 139.7 mm (5.5.50 inch) long) 2
8T-0455 Liner Projection Tool Group 1 Preparation
For checking the cylinder liner projection with the liner out of the cylinder block, ensure that the following surfaces are clean prior to measuring:
Cylinder liner flanges
Spacer plate
Spacer plate gasketFor checking the installed cylinder liner projection, ensure that the following surfaces are clean prior to measuring:
Top surface of the cylinder block
Cylinder liner bores
Cylinder liner flanges
Spacer plates
Spacer plate gasketCylinder Liner out of the Cylinder Block - Check
Illustration 1 g02247495
Use the 6V-7059 Micrometer to measure the thickness of the following items:
(X) Spacer Plate
(Y) Spacer Plate Gasket
(Z) Cylinder Liner FlangeThe cylinder liner projection depends on which spacer plate is used. Refer to Table 1.Note: To determine the cylinder liner projection, subtract the thickness of the spacer plate and gasket from the thickness of the cylinder liner flange.
Refer to Table 1 for the correct value of your cylinder liner projection based on your spacer plate.Cylinder Liner Installed in the Cylinder Block - Check
Illustration 2 g01192749
Measuring the cylinder liner projection
(1) 3H-0465 Push-Puller Plate
(2) 1P-2403 Dial Indicator
(3) 1P-2402 Gauge Body
(4) 1A-0075 Bolt and 3B-1925 Washer (COPPER)
(5) Spacer plate
(6) 1U-9895 Crossblock
Install a new gasket and spacer plate (5) on the cylinder block.
Install the cylinder liner in the cylinder block without seals or bands.
Hold spacer plate (5) and the cylinder liner in position according to the following procedure:
Install four 3B-1925 Washers (COPPER) and four 1A-0075 Bolts (4) around spacer plate (5). Tighten the bolts evenly to a torque of 95 N m (70 lb ft).
Install the following components: 1U-9895 Crossblock (6), two 3H-0465 Push-Puller Plates (1) and two 8F-6123 Bolts. Ensure that 1U-9895 Crossblock (6) is in position at the center of the cylinder liner. Ensure that the surface of the cylinder liner is clean. Tighten the bolts evenly to a torque of 70 N m (50 lb ft).
Check the distance from the bottom edge of 1U-9895 Crossblock (6) to the top edge of spacer plate (5). The vertical distance from both ends of the
Cat SIS web machinery list:
Parts gasket Caterpillar catalog:
1H9027
GASKET
631C, 641, 651, 657, 657B, 666, D337, D8H, D8K
631C, 641, 651, 657, 657B, 666, D337, D8H, D8K
9H8136
GASKET
120, 120B, 12E, 12F, 140, 140B, 14E, 920, 930, 930R, D9E
120, 120B, 12E, 12F, 140, 140B, 14E, 920, 930, 930R, D9E
1S2021
GASKET
650B, 657, 769, 824, 834, D9G
650B, 657, 769, 824, 834, D9G
1M5835
GASKET
651, 657, 769, 824, D9G
651, 657, 769, 824, D9G
1M2711
GASKET
D7F, D7G, D8H, D9G
D7F, D7G, D8H, D9G
2S8730
GASKET
D8H
D8H
2H5571
GASKET
D8H
D8H
8H7032
GASKET
D8H
D8H
9F7117
GASKET
D8H, D8K
D8H, D8K
9F7118
GASKET
D8H, D8K
D8H, D8K
2H1732
GASKET
D8H
D8H
1S1162
GASKET
D9E
D9E
8F2686
GASKET
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
9F5223
GASKET
D326F, D337, D337F, D342, D353C, D397D
D326F, D337, D337F, D342, D353C, D397D
8F6813
GASKET
D326F, D337, D337F, D342, D353C, D397D
D326F, D337, D337F, D342, D353C, D397D
8F6143
GASKET
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D379, D397D, D8H, D9E, D9G, G342C
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D379, D397D, D8H, D9E, D9G, G342C
8F9591
GASKET
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
2H4512
GASKET
D315
D315
2H5826
GASKET
D337
D337
9F1477
GASKET
D337
D337
9F1478
GASKET
594, D337, D353C, D9E, D9G
594, D337, D353C, D9E, D9G
8F8394
GASKET
D337
D337
3H6194
GASKET
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
8F5118
GASKET
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G
583H, D326F, D337, D337F, D342, D342C, D343, D353C, D375D, D397D, D8H, D9E, D9G