GASKET 8S9988 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of all maintenance including the following procedures: all adjustments, the use of proper lubricants, fluids, filters and the installation of new components due to normal wear and aging . The performance of this product may be diminished if proper maintenance intervals and procedures are not followed. Components may experience accelerated wear if proper maintenance intervals and procedures are not followed.Note: Use whichever of the following that occurs first in order to determine the maintenance intervals: fuel consumption, service hours and calendar time . Before each consecutive interval is performed, all maintenance from the previous intervals must be performed.Products that operate in severe operating conditions may require more frequent maintenance.When Required
Air Inlet Filter - Inspect/Clean/Test
Battery - Recycle
Battery - Replace
Circuit Breakers - Reset
Engine Air Cleaner Element - Replace
Generator - Dry
Generator Bearing - Lubricate
Generator Set - Test
Generator Set Alignment - Check
Generator Winding - Test
Overhaul Considerations
Rotating Rectifier - Inspect/Test
Stator Winding Temperature - Test
Varistor - Inspect
Daily
Air Prelube Pump Lubricator Oil Level - Check
Air Tank Moisture and Sediment - Drain
Control Panel - Inspect/Test
Coolant Level - Check
Electrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Air Precleaner - Check/Clean
Engine Oil Level - Check
Fuel Filter Differential Pressure - Check
Generator - Inspect
Generator Bearing Temperature - Test/Record
Generator Load - Check
Power Factor - Check
Voltage and Frequency - Check
Walk-Around Inspection
Every Week
Automatic Start/Stop - Inspect
Battery Charger - Check
Generator Lead - Check
Jacket Water Heater - Check
Space Heater - Test
Standby Generator Set Maintenance Recommendations
Every 250 Service Hours
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Oil Sample - Obtain
Every 500 Service Hours
Coolant Sample (Level 1) - Obtain
Every 750 Service Hours
Aftercooler Core - Clean/Test
Battery Electrolyte Level - Check
Belts - Inspect/Adjust/Replace
Crankshaft Vibration Damper - Inspect
Engine - Clean
Engine Crankcase Breather - Clean
Engine Oil and Filter - Change
Fan Drive Bearing - Lubricate
Hoses and Clamps - Inspect/Replace
Inlet Air System - Check
Radiator - Clean
Spark Plugs - Inspect/Adjust/Replace
Initial 750 Service Hours
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Every 750 Service Hours or Monthly
Carburetor Air/Fuel Ratio - Check/Adjust
Every 1000 Service Hours
Exhaust Piping - Check
Every 1500 Service Hours
Crankcase Blowby - Test/Record
Cylinder Pressure - Test/Record
Engine Protective Devices - Check
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Speed Sensor - Clean/Inspect
Valve Stem Projection - Measure/Record
Every 2000 Service Hours
Generator Set Vibration - Inspect
Every Year
Catalytic Converter Substrate - Inspect
Coolant Sample (Level 2) - Obtain
Engine Mounts - Inspect
Generator Winding Insulation - Test
Varistor - Check
Every 3000 Service Hours
Air Prelube Pump Lubricator Bowl - Clean
Alternator - Inspect
Driven Equipment - Check
Engine Performance - Test
Starting Motor - Inspect
Water Pump - Inspect
Every 3000 Service Hours or 4 Months
Alternator - Inspect
Generator Set Vibration - Test/Record
Stator Lead - Check
Every 3 Years
Coolant (DEAC) - Change
Coolant (NGEC) - Change
Exhaust Bypass - Inspect
Spark Plug Wires - Replace
Every 8000 Service Hours
Catalytic Converter Pressure - Test
Catalytic Converter Temperature - Test
Gas Pressure Regulator - Test
Ignition System Transformer Resistance - Test
Overhaul (Top End)
Rotating Rectifier - Check
Turbocharger - Inspect
Every 16 000 Service Hours
Catalytic Converter Substrate