1351708 GAUGE AS-OIL LEVEL Caterpillar parts
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
Rating:
Alternative (cross code) number:
CA1351708
135-1708
1351708
CA1351708
135-1708
1351708
Weight: 0.60 pounds 0 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 1351708:
Information:
Remove And Install Connecting Rod Bearings
start by: a) remove engine oil coolerb) remove fresh water pumpc) remove startersd) remove engine oil pumpe) remove oil pressure relief valve1. Fasten a hoist and remove the prelubrication oil pump and motor as a unit, (if so equipped). Weight is 105 lb. (47.3 kg).2. Remove the wiring harness and plate for the prelubrication oil pump and motor. 3. Remove the bolts (1) that hold inspection covers to block. Remove the inspection covers (2) from each side of block.4. Turn crankshaft (in the direction of normal rotation) until the rod caps (4) can be removed through the opening. 5. Remove the bolts (3) from each rod cap. Remove the rod cap (4). 6. Remove the bearing (5) from the rod cap. 7. Push the connecting rods (6) away from crankshaft. 8. Remove the upper half of bearings from the connecting rods.9. Install the upper half of new rod bearings in the connecting rods. Put clean SAE 30 engine oil on the bearings and crankshaft Journal. Pull the connecting rods with bearing into position on crankshaft. Be sure the tab on back of bearing fits in tab groove (slot) in connecting rod.10. Install lower half of new bearings in caps. Put clean SAE 30 engine oil on bearings. Be sure the tab on back of bearing fits in tab groove (slot) of cap.11. Check the bearing clearance with wire (A). Install bearing cap on connecting rod. Put clean SAE 30 engine oil on threads of rod bolts. Install the rod bolts. Tighten the rod bolts first to a torque of 40 4 lb. ft. (55 5 N m). Put a mark on bolt heads and bearing caps. Tighten the bolts again 120° from the mark.
TYPICAL EXAMPLE12. Remove the cap. Measure thickness of the wire. The clearance between a new rod bearing and crankshaft Journal must be .0031 to .0073 in. (0.079 to 0.185 mm). The maximum permissible clearance is .012 in. (0.30 mm).13. Put the caps in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 40 4 lb. ft. (55 5 N m). Put a mark on the bolt heads and bearing caps then tighten the bolts 120° more. Locks and cotter pins are not necessary with this method to tighten the bolts, even though the bolt has a hole.14. Install the inspection covers with new gaskets.15. Install the plate and wiring harness for pre-lubrication oil pump and motor (if so equipped). Install the prelubrication oil pump and motor with a hoist. Weight is 105 lb. (47.3 kg)end by: a) install fresh water pumpb) install engine oil pumpc) install engine oil coolerd) install starterse) install oil pressure relief valve
start by: a) remove engine oil coolerb) remove fresh water pumpc) remove startersd) remove engine oil pumpe) remove oil pressure relief valve1. Fasten a hoist and remove the prelubrication oil pump and motor as a unit, (if so equipped). Weight is 105 lb. (47.3 kg).2. Remove the wiring harness and plate for the prelubrication oil pump and motor. 3. Remove the bolts (1) that hold inspection covers to block. Remove the inspection covers (2) from each side of block.4. Turn crankshaft (in the direction of normal rotation) until the rod caps (4) can be removed through the opening. 5. Remove the bolts (3) from each rod cap. Remove the rod cap (4). 6. Remove the bearing (5) from the rod cap. 7. Push the connecting rods (6) away from crankshaft. 8. Remove the upper half of bearings from the connecting rods.9. Install the upper half of new rod bearings in the connecting rods. Put clean SAE 30 engine oil on the bearings and crankshaft Journal. Pull the connecting rods with bearing into position on crankshaft. Be sure the tab on back of bearing fits in tab groove (slot) in connecting rod.10. Install lower half of new bearings in caps. Put clean SAE 30 engine oil on bearings. Be sure the tab on back of bearing fits in tab groove (slot) of cap.11. Check the bearing clearance with wire (A). Install bearing cap on connecting rod. Put clean SAE 30 engine oil on threads of rod bolts. Install the rod bolts. Tighten the rod bolts first to a torque of 40 4 lb. ft. (55 5 N m). Put a mark on bolt heads and bearing caps. Tighten the bolts again 120° from the mark.
TYPICAL EXAMPLE12. Remove the cap. Measure thickness of the wire. The clearance between a new rod bearing and crankshaft Journal must be .0031 to .0073 in. (0.079 to 0.185 mm). The maximum permissible clearance is .012 in. (0.30 mm).13. Put the caps in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 40 4 lb. ft. (55 5 N m). Put a mark on the bolt heads and bearing caps then tighten the bolts 120° more. Locks and cotter pins are not necessary with this method to tighten the bolts, even though the bolt has a hole.14. Install the inspection covers with new gaskets.15. Install the plate and wiring harness for pre-lubrication oil pump and motor (if so equipped). Install the prelubrication oil pump and motor with a hoist. Weight is 105 lb. (47.3 kg)end by: a) install fresh water pumpb) install engine oil pumpc) install engine oil coolerd) install starterse) install oil pressure relief valve
Cat SIS web machinery list:
Parts gauge Caterpillar catalog:
9Y9236
GAUGE-SIGHT
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 16M, 24H, 24M, 30/30, 3176B, 3176C, 3196, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3406E, 3408B, 3412, 3412C, 3456, 345D, 345D L, 34...
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 16M, 24H, 24M, 30/30, 3176B, 3176C, 3196, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3406E, 3408B, 3412, 3412C, 3456, 345D, 345D L, 34...
1U7234
GAUGE GP-FEELER
307C, 311C, 3126, 3304, 3304B, 3306, 3306B, 3406, 3406C, 3406E, 3408E, 3412, 3412C, 3412E, 350, 3508, 3508B, 3512, 3512B, 3516, 3516B, 589, 938F, 938G, 950F, 950F II, 950G, 962G, D5B, D6D, D7H, D8R II...
307C, 311C, 3126, 3304, 3304B, 3306, 3306B, 3406, 3406C, 3406E, 3408E, 3412, 3412C, 3412E, 350, 3508, 3508B, 3512, 3512B, 3516, 3516B, 589, 938F, 938G, 950F, 950F II, 950G, 962G, D5B, D6D, D7H, D8R II...
9C6327
GAUGE AS-OIL LEVEL (DIPSTICK)
2470C, 2570C, 2670C, 2864C, 518C, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966F, 966F II,...
2470C, 2570C, 2670C, 2864C, 518C, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966F, 966F II,...
2154683
GAUGE-OIL LEVEL
938G II, 950G II, 962G II, IT38G II, IT62G II
938G II, 950G II, 962G II, IT38G II, IT62G II
3345274
GAUGE AS-LIQUID LEVEL
938G II, 950G II, 962G II, IT38G II
938G II, 950G II, 962G II, IT38G II
2465717
GAUGE GP-OIL LEVEL (DIPSTICK)
938G II, 950G II, 962G II, IT38G II, IT62G II
938G II, 950G II, 962G II, IT38G II, IT62G II
2615689
GAUGE AS
950H, 962H, IT62H
950H, 962H, IT62H
3453889
GAUGE AS-OIL LEVEL (DIPSTICK)
950H, 962H, IT62H
950H, 962H, IT62H
4322314
GAUGE GP-OIL LEVEL (DIPSTICK)
950H, 962H, IT62H
950H, 962H, IT62H
1131200
GAUGE-OIL LEVEL (DIPSTICK)
950F, 950F II, 960F, 962G
950F, 950F II, 960F, 962G
3725156
GAUGE GP-OIL LEVEL (DIPSTICK)
950K, 962K
950K, 962K
3725157
GAUGE AS-OIL LEVEL (DIPSTICK)
950K, 962K
950K, 962K
1307189
GAUGE-OIL LEVEL
938G, 950G, 962G, IT38G, IT62G
938G, 950G, 962G, IT38G, IT62G
2W0521
GAUGE AS-OIL LEVEL (DIPSTICK)
631E, 637E
631E, 637E
1445374
GAUGE-SIGHT
621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G
621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G
2470272
GAUGE AS-OIL LEVEL (DIPSTICK)
631D, 631E, 631G, 633E II, 637D, 637E, 637G
631D, 631E, 631G, 633E II, 637D, 637E, 637G
1251197
GAUGE AS-OIL LEVEL
631D, 631E, 631G, 633E II, 637E, 637G
631D, 631E, 631G, 633E II, 637E, 637G
2022533
GAUGE GP-SIGHT
902, 906
902, 906
1572287
GAUGE
902
902
1494456
GAUGE AS
938G, 938G II, 938H, IT38G, IT38G II, IT38H
938G, 938G II, 938H, IT38G, IT38G II, IT38H
9C6327
GAUGE AS-OIL LEVEL (DIPSTICK)
2470C, 2570C, 2670C, 2864C, 518C, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966F, 966F II,...
2470C, 2570C, 2670C, 2864C, 518C, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966F, 966F II,...