GAUGE-OIL LEVEL 1487225 - Caterpillar

Electric Power Generation: SR4B (S/N: G5Y1-UP)Engine: 3516C (S/N: KEN1-UP)Power Module: C32 POWER MODULE (S/N: MED1-UP)Introduction
This document provides proper procedures to download a program to power generation equipment. This procedure uses the Execloader software for downloading.Items that are Required to Download the Program
Illustration 1 g01451818
The following items will be required to perform the download.
Laptop computer
Level 1 Apploader software or Level 2 Concept software
Access to the Internet
Communication cable between the laptop computer and the PLC (1)
PCMCIA adapter (2). This adapter is required for laptop computers without type 3 PCMCIA slots.
Modbus Plus card (3). This is a type 3 PCMCIA card. The Modbus Plus part number for this card is 416 NHM 21 234. Connecting the Hardware
Note: Ensure that the Wincox MBX software is installed on the computer. Also ensure that Virtual MBX software is installed on the computer. The Modbus Plus card (3) should not then be plugged into the computer without this software.
Illustration 2 g01451905
Insert the Modbus Plus card (3) into the PCMCIA slot on the computer. Use the type 3 PCMCIA adapter (2) if your computer does not have a type 3 PCMCIA slot.
Illustration 3 g01451912
Verify that the red "ERR" LED (6) is flashing. Also verify that the green "COM" LED (7) is flashing.
Illustration 4 g01451924
Connect one end of the Modbus Plus communication cable (1) to the laptop computer. Connect the other end of the cable to the communication port (8) for the switchgear. Downloading the Software
Illustration 5 g01453165
Open the Concept EXECloader program.
Illustration 6 g01453176
When the EXECloader screen appears, click "Next".
Illustration 7 g01453177
From the "Communication Protocol" screen, verify that the Modbus Plus protocol is selected. Click "Next".
Illustration 8 g01453178
From the "Modbus Plus Target" screen, click the "Re-Scan" button. Select the target node for the download. Click "Next" after the node has been selected.
Illustration 9 g01453181
When the "Operation" screen appears, click "Browse".
Illustration 10 g01453182
Use table 1 to select the correct .bin file for the application. The correct file is determined by the type of Momentum processor. Navigate through the "Dat" directory in order to locate the correct .bin file. Double click on the correct file in order to select that file for downloading to the PLC. Click "Next".
Table 1
Concept Version     Momentum Version    
171 CCS 7X0 X0 171 CCS 7X0 X0     171 CCC9X0 X0     171 CCC 9X0 30    
171 CCS 7X0 X10 171 CCC 7X0 10     (LL984 only)     (IEC only)    
(LL984 only)            
Functionality
2.5 SR1     M1v203.bin     M1IEC250.bin     M1EV104.bin     M1EWI250.bin    
2.5 SR2     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2a     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2b     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2c     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2d     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2e     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2f     M1v203.bin     M1V204D.bin     M1EV106.bin     M1EV106D.bin    
2.5 SR2g     M1LLV207.bin     M1V210E.bin     M1EV120.bin     M1EV122E.bin    
2.6 SR1     M1LLV207.bin