1969942 GAUGE AS-OIL LEVEL (DIPSTICK) Caterpillar parts
980G II, 980H
Rating:
Alternative (cross code) number:
CA1969942
196-9942
1969942
CA1969942
196-9942
1969942
Weight: 0.11 pounds 0 kg.
WHEEL LOADER,
Information:
open circuit is a failure of an electrical circuit that results in no flow of electrical current. An open circuit is can be caused by a break in a circuit wire. Most often, an open circuit is caused by a poor connection or a failed connection in one of the electrical connectors that is used in a circuit. The following procedure is a way to check for an open or a poor connection in a circuit.TEST FOR AN OPEN CIRCUIT.
Identify the connectors and the wire numbers of the suspect circuits. Use the Electrical System Schematic of the machine to identify the circuits.
Disconnect the negative battery cable and turn the key start switch to the OFF position.
Disconnect the component and the ECM from the wiring harness.
At one of the disconnected harness connections, place a jumper wire from the contact of the suspect wire to frame ground.
At the other connector of the machine harness, use the multimeter probes to measure the resistance from the contact of the suspect wire to frame ground.Expected Result: The resistance is less than 5 ohms. OK - The resistance is less than 5 ohms. The harness circuit is correct.Stop. NOT OK - The resistance is greater than 5000 ohms. There is an open in the machine harness.Repair: Repair the machine harness or replace the machine harness.Stop.When the resistance of a good circuit is measured, less than 5.0 ohms of resistance is expected. In a circuit that has an electrical wire or a connection that is completely open (broken or no connection), the flow of electrical current through the circuit is interrupted. A circuit that is completely open due to a broken wire or no connection in a connector will measure greater than 5000 ohms of resistance.Many times a circuit is not completely open and will allow some current to pass through, however, not enough current will pass to allow the circuit to function properly. This can be caused by a wire that is partially broken but still is intact enough to allow a small amount of current to pass. Partial breaks in a wire are difficult to diagnose because the resistance measurement may check OK through the section of wire that is still intact. Partial breaks in a wire are not common. When a partial break is suspected in a wire, the current through the circuit should be checked under load in order to verify that the correct amount of current is present.Most often, a resistance measurement of greater than 5.0 ohms and less than 5000 ohms is due to a poor connection in a circuit connector. The connector contacts may be corroded due to moisture that has entered the connector body. A connector pin or socket may not have been seated securely in the connector body and is not making good contact or a wire may be broken at the point where the pin or socket is connected. When checking for problems in a circuit, the connectors in the circuit should be examined closely.When
Identify the connectors and the wire numbers of the suspect circuits. Use the Electrical System Schematic of the machine to identify the circuits.
Disconnect the negative battery cable and turn the key start switch to the OFF position.
Disconnect the component and the ECM from the wiring harness.
At one of the disconnected harness connections, place a jumper wire from the contact of the suspect wire to frame ground.
At the other connector of the machine harness, use the multimeter probes to measure the resistance from the contact of the suspect wire to frame ground.Expected Result: The resistance is less than 5 ohms. OK - The resistance is less than 5 ohms. The harness circuit is correct.Stop. NOT OK - The resistance is greater than 5000 ohms. There is an open in the machine harness.Repair: Repair the machine harness or replace the machine harness.Stop.When the resistance of a good circuit is measured, less than 5.0 ohms of resistance is expected. In a circuit that has an electrical wire or a connection that is completely open (broken or no connection), the flow of electrical current through the circuit is interrupted. A circuit that is completely open due to a broken wire or no connection in a connector will measure greater than 5000 ohms of resistance.Many times a circuit is not completely open and will allow some current to pass through, however, not enough current will pass to allow the circuit to function properly. This can be caused by a wire that is partially broken but still is intact enough to allow a small amount of current to pass. Partial breaks in a wire are difficult to diagnose because the resistance measurement may check OK through the section of wire that is still intact. Partial breaks in a wire are not common. When a partial break is suspected in a wire, the current through the circuit should be checked under load in order to verify that the correct amount of current is present.Most often, a resistance measurement of greater than 5.0 ohms and less than 5000 ohms is due to a poor connection in a circuit connector. The connector contacts may be corroded due to moisture that has entered the connector body. A connector pin or socket may not have been seated securely in the connector body and is not making good contact or a wire may be broken at the point where the pin or socket is connected. When checking for problems in a circuit, the connectors in the circuit should be examined closely.When
Caterpillar parts catalog:
Parts gauge Caterpillar catalog:
1851572
GAUGE GP-OIL LEVEL (DIPSTICK)
980G II, 980H
980G II, 980H
3007448
GAUGE GP-OIL LEVEL (DIPSTICK)
980G, 980H
980G, 980H
2Q7705
GAUGE GP-OIL LEVEL (DIPSTICK)
980G, 980G II
980G, 980G II
9Y9236
GAUGE-SIGHT
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 16M, 24H, 24M, 30/30, 3176B, 3176C, 3196, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3406E, 3408B, 3412, 3412C, 3456, 345D, 345D L, 34...
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 16M, 24H, 24M, 30/30, 3176B, 3176C, 3196, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3406E, 3408B, 3412, 3412C, 3456, 345D, 345D L, 34...
1039603
GAUGE-SIGHT
613G, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 69D, 769D, 770, 771D, 772, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776D, 777D, 777F, 777G,...
613G, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 69D, 769D, 770, 771D, 772, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776D, 777D, 777F, 777G,...
1425603
GAUGE AS
824G, 824G II, 825G, 825G II, 826G, 826G II, 980F II, 980G, 980G II, 980H, 988F II
824G, 824G II, 825G, 825G II, 826G, 826G II, 980F II, 980G, 980G II, 980H, 988F II
3007445
GAUGE AS-OIL LEVEL (DIPSTICK)
980G, 980H
980G, 980H
2554888
GAUGE AS-SIGHT
824G II, 824H, 825G II, 825H, 826G II, 826H, 980H, 980K, 980K HLG, 980M, 982M, 986H
824G II, 824H, 825G II, 825H, 826G II, 826H, 980H, 980K, 980K HLG, 980M, 982M, 986H
1236997
GAUGE AS-OIL LEVEL (DIPSTICK)
994D, 994F, 994H
994D, 994F, 994H
1346635
GAUGE AS-OIL LEVEL
814F, 814F II, 815F, 815F II, 966G, 966G II, 966H, 972G, 972G II, 972H
814F, 814F II, 815F, 815F II, 966G, 966G II, 966H, 972G, 972G II, 972H
1390241
GAUGE AS-OIL LEVEL (DIPSTICK)
966F, 966F II, 966G, 972G
966F, 966F II, 966G, 972G
1240665
GAUGE-LIQUID LEVEL
824K, 825K, 826K, 844H, 844K, 854G, 854K, 988G, 988H, 990H, 990K, 992G, 992K, 993K, AD45, AD45B, AD55, AE40 II
824K, 825K, 826K, 844H, 844K, 854G, 854K, 988G, 988H, 990H, 990K, 992G, 992K, 993K, AD45, AD45B, AD55, AE40 II
1223177
GAUGE AS-OIL LEVEL
854G, 992G
854G, 992G
1326277
GAUGE AS-LIQUID LEVEL
834G, 834H, 834K, 836G, 836H, 836K, 980G, 988K, AD30, AD55B, AD60, R1300, R1300G, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
834G, 834H, 834K, 836G, 836H, 836K, 980G, 988K, AD30, AD55B, AD60, R1300, R1300G, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
3007445
GAUGE AS-OIL LEVEL (DIPSTICK)
980G, 980H
980G, 980H
2912659
GAUGE AS-LIQUID LEVEL
994F, 994H
994F, 994H
2065090
GAUGE
844, 844H, 854K, 990 II, 990H, 992K, AD55B
844, 844H, 854K, 990 II, 990H, 992K, AD55B
2844930
GAUGE AS-OIL LEVEL (DIPSTICK)
345D L, 966G II, 966H, 972G II, 972H, D8N
345D L, 966G II, 966H, 972G II, 972H, D8N
2285226
GAUGE AS-OIL LEVEL
966G II, 972G II
966G II, 972G II