6N9885 GAUGE (engine oil pressure) Caterpillar parts
225, 225D, 227, 229, 231D
Rating:
Alternative (cross code) number:
CA6N9885
6N-9885
6N9885
CA6N9885
6N-9885
6N9885
Weight: 0.50 pounds 0 kg.
Information:
CALIBRATION POINT 1
0
CALIBRATION POINT 2
103
CALIBRATION POINT 3
208
CALIBRATION POINT 4
519
CALIBRATION POINT 5
0
MAXIMUM PRESSURE
519
kPa
MINIMUM PRESSURE
0
kPa
OPERATING VOLTAGE
000000000012
V
TYPE
MECHANICAL
EXCAVATOR, LOGGER,
Number on catalog scheme:
2
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1863 Retaining Ring Pliers 1
B 1P-1861 Retaining Ring Pliers 1 Start By:
Remove the transfer gear. Refer to Disassembly and Assembly, "Transfer Gear (Idler) - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Illustration 1 g01196907
Use Tooling (A) in order to remove retaining ring (1).
Illustration 2 g01196908
Use a suitable press in order to remove shaft (2).
Illustration 3 g01196909
Remove bearing (3). Note: Bearing (3) will be destroyed on removal.
Use Tooling (B) in order to remove retaining ring (4) from gear (5).
Remove spacer (6). Use a suitable press in order to remove bearing (7).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1863 Retaining Ring Pliers 1
B 1P-1861 Retaining Ring Pliers 1 Start By:
Remove the transfer gear. Refer to Disassembly and Assembly, "Transfer Gear (Idler) - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Illustration 1 g01196907
Use Tooling (A) in order to remove retaining ring (1).
Illustration 2 g01196908
Use a suitable press in order to remove shaft (2).
Illustration 3 g01196909
Remove bearing (3). Note: Bearing (3) will be destroyed on removal.
Use Tooling (B) in order to remove retaining ring (4) from gear (5).
Remove spacer (6). Use a suitable press in order to remove bearing (7).
Caterpillar parts catalog:
Parts gauge Caterpillar catalog:
120, 120B, 120G, 12G, 130G, 140B, 140G, 1676, 16G, 215, 225, 235, 245, 3126, 3160, 3176B, 3208, 3304, 3304B, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412...
120G, 12G, 130G, 140G, 14G, 160G, 16G, 225, 231D, 235B, 235C, 235D, 30/30, 3114, 3116, 3126, 3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3508, 3512, 3516, 3516B, 3606...
225, 235, 3208, 3306, 3406, 3406B, 3408, 3412, 3508, 3512, 3516, 561B, 561C, 571G, 572G, 583H, 583K, 594, 594H, 613, 613B, 941, 951B, 955H, 955K, 955L, 977H, 977K, 983, D315, D320A, D326F, D330A, D333...
9S5578
GAUGE-OIL PRESSURE
225, 3160, 3406, 3406B, 3408, 3412, 3412C, 613, 613B, 641B, 650B, 657B, 666B
225, 3160, 3406, 3406B, 3408, 3412, 3412C, 613, 613B, 641B, 650B, 657B, 666B
225D, 231D, 3208, CS-551
3N2981
GAUGE-OIL LEVEL
225, 3208
225, 3208
225, 3208, 613C
6C3061
GAUGE-FUEL LEVEL
225D, 229D, 231D
225D, 229D, 231D
8N9611
GAUGE
227, D8L
227, D8L
1N3809
GAUGE ASSEM.
245, 245B
245, 245B
215, 215B, 215C, 215D, 225, 225D, 229, 229D, 235, 235B, 235C, 235D, 245, 245B, 245D, 955L, 977L, 983B
6N4200
GAUGE ASSEM.
621R, 627B, D6C
621R, 627B, D6C
245, 245B
6N6511
GAUGE ASSEM.
215, D3B, D3C
215, D3B, D3C