7C0707 GAUGE-OIL LEVEL (DIPSTICK) Caterpillar parts
3114, 3116, 446B, 446D, 928F, IT28F, RT100
Rating:
Alternative (cross code) number:
CA7C0707
7C-0707
7C0707
CA7C0707
7C-0707
7C0707
Weight: 0.04 pounds 0 kg.
BACKHOE LOADER, WHEEL LOADER,
Compatible equipment models: 7C0707:
Information:
Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-5096     Dial Indicator Group     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil to the upper main bearing. Do not apply engine oil to the back side of the bearing surfaces. Install the upper main bearings in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01128041
Apply clean engine oil to the journals of the crankshaft bearing. Attach a suitable lifting device to crankshaft (1). The weight of crankshaft (1) is approximately 62 kg (137 lb). Align the identification marks on the gear train. Install crankshaft (1) in the cylinder block.
Clean the bearing surface of main bearing caps (3). Install the lower main bearings in the main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil to the lower main bearings. Do not apply engine oil to the back side of the bearing surfaces.
Install main bearing caps (3) with the part numbers toward the right hand side of the cylinder block. Ensure that the main bearing caps have numbers 1 through 7. The numbers should start at the front of the engine. Apply clean engine oil or Molylube to the bolt threads and the washers.Note: When the bolts for the rear main bearing cap are tightened, slide the main bearing cap as far forward as possible until the cap is against the bolts. Hold the main bearing cap in this position and tighten the bolts.
Install bolts (2) for main bearing caps (3). Tighten bolts (2) to a torque of 54 7 N m (40 5 lb ft).
Turn bolts (2) for an additional 90 5 degrees (1/4 turn).
Check the end play of crankshaft (1) with Tooling (A). The end play must be 0.07 mm to 0.32 mm (0.003 inch to 0.013 inch).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install".
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-5096     Dial Indicator Group     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil to the upper main bearing. Do not apply engine oil to the back side of the bearing surfaces. Install the upper main bearings in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01128041
Apply clean engine oil to the journals of the crankshaft bearing. Attach a suitable lifting device to crankshaft (1). The weight of crankshaft (1) is approximately 62 kg (137 lb). Align the identification marks on the gear train. Install crankshaft (1) in the cylinder block.
Clean the bearing surface of main bearing caps (3). Install the lower main bearings in the main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil to the lower main bearings. Do not apply engine oil to the back side of the bearing surfaces.
Install main bearing caps (3) with the part numbers toward the right hand side of the cylinder block. Ensure that the main bearing caps have numbers 1 through 7. The numbers should start at the front of the engine. Apply clean engine oil or Molylube to the bolt threads and the washers.Note: When the bolts for the rear main bearing cap are tightened, slide the main bearing cap as far forward as possible until the cap is against the bolts. Hold the main bearing cap in this position and tighten the bolts.
Install bolts (2) for main bearing caps (3). Tighten bolts (2) to a torque of 54 7 N m (40 5 lb ft).
Turn bolts (2) for an additional 90 5 degrees (1/4 turn).
Check the end play of crankshaft (1) with Tooling (A). The end play must be 0.07 mm to 0.32 mm (0.003 inch to 0.013 inch).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install".
Caterpillar parts catalog:
Parts gauge Caterpillar catalog:
3E8534
GAUGE GP-OIL TEMPERATURE
416, 416B, 426B, 428B, 446, 446B
416, 416B, 426B, 428B, 446, 446B
3E8535
GAUGE GP-COOLANT TEMPERATURE
416, 416B, 426B, 428B, 446, 446B, AP-1000, AP-1050, AP-800
416, 416B, 426B, 428B, 446, 446B, AP-1000, AP-1050, AP-800
9R7211
GAUGE AS-OIL LEVEL (DIPSTICK)
416, 416B, 428B, 436, 438B
416, 416B, 428B, 436, 438B
1356510
GAUGE AS
416B, 426B, 428B
416B, 426B, 428B
7W2060
GAUGE
3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3508, 3512, 3516, C-15, D398A, G3304, G342C
3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3508, 3512, 3516, C-15, D398A, G3304, G342C
1356469
GAUGE AS-OIL LEVEL (DIPSTICK)
235B, 3306, 572R, D7G, D7G2, D7H, D7R
235B, 3306, 572R, D7G, D7G2, D7H, D7R
4P8508
GAUGE AS-OIL LEVEL (DIPSTICK)
75, 75C, 85C
75, 75C, 85C
1128871
GAUGE-OIL LEVEL (DIPSTICK)
35, 45, 55
35, 45, 55
9R8887
GAUGE AS-OIL LEVEL (DIPSTICK)
446, 446B
446, 446B