1141513 GEAR & BEARING GP-SWING Caterpillar parts
325B L
Rating:
Alternative (cross code) number:
CA1141513
114-1513
1141513
CA1141513
114-1513
1141513
EXCAVATOR,
Compatible equipment models: 1141513:
Number on catalog scheme:
For full view, you need register
Information:
Table 1
Required Tools
Part Number Part Name Qty
8T-5096 Dial Indicator Group 1 Face Runout (Axial Eccentricity) of the Flywheel housing
Illustration 1 g00285931
Face runout check
Position the magnetic base of the dial indicator on the crankshaft flange. Position the contact of the dial indicator on the face of the flywheel housing.
Force the crankshaft to the rear in order to remove the clearance for the main bearing.
Illustration 2 g00326434
Locations for measuring the face runout of the flywheel housing
(A) Bottom
(B) Right side
(C) Top
(D) Left side
Set the dial indicator to 0.0 mm (0.00 inch) at location (A). Turn the crankshaft in order to measure the face runout at locations (B), (C), and (D).
Maximum face runout Calculate the difference between the lowest measurement and the highest measurement of the four locations. This difference must not be greater than the limit that is given in the following table. This difference is the maximum permissible face runout of the flywheel housing.
Table 2
Bore Of The Housing Flange Maximum Permissible Face Runout
362 mm (14.25 inch) 0.23 mm (0.009 inch)
410 mm (16.14 inch) 0.25 mm (0.010 inch)
448 mm (17.64 inch) 0.28 mm (0.011 inch)
511 mm (20.12 inch) 0.30 mm (0.012 inch)
584 mm (22.99 inch) 0.36 mm (0.014 inch)
648 mm (25.51 inch) 0.41 mm (0.016 inch)
787 mm (30.98 inch) 0.48 mm (0.019 inch) Bore Runout (Radial Eccentricity) of the Flywheel Housing
Illustration 3 g00285934
Bore runout check
Illustration 4 g00326438
Locations for measuring the bore runout of the flywheel housing
(1) Bottom
(2) Right side
(3) Top
(4) Left side
Fasten the magnetic base of the dial indicator to the crankshaft flange. Adjust the contact of the dial indicator in order to touch the bore of the flywheel housing at location (1). Set the pointer of the dial indicator to 0.0 mm (0.00 inch).
Push the crankshaft to the rear in order to remove the main bearing clearance before the measurement is taken at each location.
Turn the crankshaft. Record the dial indicator reading at locations (2), (3), and (4).
Calculate the difference between the lowest measurement and the highest measurement of the four locations. This difference must not be greater than 0.30 mm (0.012 inch). This dimension is the maximum permissible distance for the bore runout of the flywheel housing.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325...
322 FM L, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330D FM, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 34...
322 FM L, 322B L, 322B LN, 325B, 325B L, 330D FM, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 568 FM LL, M32...
320B, 322B L, 325 L, 325B, 325B L, OEMS
320B, 322B L, 325 L, 325B, 325B L, OEMS
320B, 322B L, 325 L, 325B, 325B L, OEMS
320B, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
320B, 322B L, 325 L, 325B, 325B L, OEMS
320B, 322B L, 325 L, 325B, 325B L, OEMS
320B, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
320B, 322B L, 325 L, 325B, 325B L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, OEMS
320B, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
1141475
GEAR & BEARING GP-SWING
325B, 325B L
325B, 325B L
1912557
GEAR & BEARING GP-SWING
330B, 330B L
330B, 330B L
1912555
GEAR & BEARING GP-SWING
325B L, M325B
325B L, M325B