1276329 GEAR-INPUT Caterpillar parts
963C
Rating:
Alternative (cross code) number:
CA1276329
127-6329
1276329
CA1276329
127-6329
1276329
Weight: 15 pounds 7 kg.
TRACK LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2021-09-23
2020-02-12
Compatible equipment models: 1276329:
Information:
Test Step 1. Verify Activation of the "Idle Shutdown Timer"
Connect Cat ET to the data link connector.
Access the "Configuration" screen on Cat ET.
Record the programmed time for the "Idle Shutdown Timer". Note: The "Idle Shutdown Timer" must be between 1 and 1440 minutes. The timer is disabled if the "Idle Shutdown Timer" is programmed to 0.
Record the programmed status of the parameter for the "Allow Idle Shutdown Override" and the "Idle Shutdown Timer Maximum RPM".
Start the engine. Allow the engine to warm up until the coolant temperature is 38 °C (100 °F). Allow the engine to operate at the programmed low idle and turn off any unnecessary accessory devices.
Ensure that all unnecessary loads are turned off. The "Idle Shutdown Timer Maximum RPM" can be programmed to allow the timer to be reset by increasing the engine rpm above the programmed limit. Ensure that the accelerator is not being depressed so that the rpm increases beyond the programmed limit.
Ensure that the status for "Vehicle Speed" on Cat ET is 0 km/h (0 mph).
Ensure that the engine speed on the status screen is at "Low Idle".
Ensure that the clutch pedal is not depressed. Ensure that the brake pedal is not depressed.
Ensure that the status of the PTO on/off switch is off.
Observe the "Idle Shutdown Status". Expected Result:The "Idle Shutdown Status" indicates "Counting" or the "Idle Shutdown Status" indicates "Not Active".Results:
Counting - The "Idle Shutdown Status" indicates "Counting". The ECM is reading the proper conditions for the activation of the "Idle Shutdown Timer". Proceed to Test Step 2.
Not Active - The "Idle Shutdown Status" indicates "Not Active". The ECM is not reading the proper conditions for activation of the "Idle Shutdown Timer". Proceed to Test Step 3.Test Step 2. Verify the Driver Alert Function for Idle Shutdown and the Override Function for Idle Shutdown
Access the "Configuration" screen on Cat ET.
Reprogram the "Idle Shutdown Timer" to 1 minute for this test.
Observe the following items during the 30 second period before the programmed shutdown time:
Check engine lamp on the vehicle's dash panel
Idle shutdown status on Cat ET
If the "Allow Idle Shutdown Override" parameter is programmed to "YES", perform either of the following actions in order to override the shutdown:
Depress the clutch pedal.
Depress the service brake pedal.Note: This action must be accomplished while the check engine lamp is flashing. The check engine lamp flashes during the 30 second period before the programmed shutdown time. The 90 second Driver Alert period can be tested by programming the "Idle Shutdown Timer" to 2 minutes or longer.
Reprogram the "Idle Shutdown Timer" to the original value. Expected Result:During the 30 to 90 second Driver Alert period before the scheduled shutdown, the status changes from "Counting" to "Driver Alert" and the check engine lamp flashes rapidly. If the "Allow Idle Shutdown Override" is programmed to "YES", the "Idle Shutdown Status" changes to "Override" after the pedals are depressed.Result 1 The "Idle Shutdown Timer" behaves in the manner that is described above.Result 2 The check engine lamp did not flash
Connect Cat ET to the data link connector.
Access the "Configuration" screen on Cat ET.
Record the programmed time for the "Idle Shutdown Timer". Note: The "Idle Shutdown Timer" must be between 1 and 1440 minutes. The timer is disabled if the "Idle Shutdown Timer" is programmed to 0.
Record the programmed status of the parameter for the "Allow Idle Shutdown Override" and the "Idle Shutdown Timer Maximum RPM".
Start the engine. Allow the engine to warm up until the coolant temperature is 38 °C (100 °F). Allow the engine to operate at the programmed low idle and turn off any unnecessary accessory devices.
Ensure that all unnecessary loads are turned off. The "Idle Shutdown Timer Maximum RPM" can be programmed to allow the timer to be reset by increasing the engine rpm above the programmed limit. Ensure that the accelerator is not being depressed so that the rpm increases beyond the programmed limit.
Ensure that the status for "Vehicle Speed" on Cat ET is 0 km/h (0 mph).
Ensure that the engine speed on the status screen is at "Low Idle".
Ensure that the clutch pedal is not depressed. Ensure that the brake pedal is not depressed.
Ensure that the status of the PTO on/off switch is off.
Observe the "Idle Shutdown Status". Expected Result:The "Idle Shutdown Status" indicates "Counting" or the "Idle Shutdown Status" indicates "Not Active".Results:
Counting - The "Idle Shutdown Status" indicates "Counting". The ECM is reading the proper conditions for the activation of the "Idle Shutdown Timer". Proceed to Test Step 2.
Not Active - The "Idle Shutdown Status" indicates "Not Active". The ECM is not reading the proper conditions for activation of the "Idle Shutdown Timer". Proceed to Test Step 3.Test Step 2. Verify the Driver Alert Function for Idle Shutdown and the Override Function for Idle Shutdown
Access the "Configuration" screen on Cat ET.
Reprogram the "Idle Shutdown Timer" to 1 minute for this test.
Observe the following items during the 30 second period before the programmed shutdown time:
Check engine lamp on the vehicle's dash panel
Idle shutdown status on Cat ET
If the "Allow Idle Shutdown Override" parameter is programmed to "YES", perform either of the following actions in order to override the shutdown:
Depress the clutch pedal.
Depress the service brake pedal.Note: This action must be accomplished while the check engine lamp is flashing. The check engine lamp flashes during the 30 second period before the programmed shutdown time. The 90 second Driver Alert period can be tested by programming the "Idle Shutdown Timer" to 2 minutes or longer.
Reprogram the "Idle Shutdown Timer" to the original value. Expected Result:During the 30 to 90 second Driver Alert period before the scheduled shutdown, the status changes from "Counting" to "Driver Alert" and the check engine lamp flashes rapidly. If the "Allow Idle Shutdown Override" is programmed to "YES", the "Idle Shutdown Status" changes to "Override" after the pedals are depressed.Result 1 The "Idle Shutdown Timer" behaves in the manner that is described above.Result 2 The check engine lamp did not flash
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
2051321
GEAR GP-FRONT
120H, 120K, 120K 2, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D...
120H, 120K, 120K 2, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D...
7W4070
GEAR
120H, 120H ES, 120H NA, 135H, 135H NA, 205B, 214B, 3114, 3116, 3126, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574, 5...
120H, 120H ES, 120H NA, 135H, 135H NA, 205B, 214B, 3114, 3116, 3126, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574, 5...
2W8147
GEAR
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 205B, 213B, 214B, 2290, 2390, 2391, 2491, 2590, 30/30, 3114, 3116, 3126, 3126B...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 205B, 213B, 214B, 2290, 2390, 2391, 2491, 2590, 30/30, 3114, 3116, 3126, 3126B...
2W8476
GEAR AS-IDLER
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 325C, 330C L, 35, 446B, 446D, 45, 525B, 533, 535B, 5...
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 325C, 330C L, 35, 446B, 446D, 45, 525B, 533, 535B, 5...
7W9740
GEAR AS-IDLER
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, ...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, ...
2W8085
GEAR-PUMP DRIVE
120H, 120H ES, 120H NA, 135H, 135H NA, 205B, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 325C, 35, 446B, 446D, 45, 525B, 533, 535B, 539...
120H, 120H ES, 120H NA, 135H, 135H NA, 205B, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 325C, 35, 446B, 446D, 45, 525B, 533, 535B, 539...
7W5095
GEAR-FLYWHEEL
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3208, 35, 45, 525B, 525C, 533, 535B, 535C, 543, 545C, 55, 561M, 561N, 613C II...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3208, 35, 45, 525B, 525C, 533, 535B, 535C, 543, 545C, 55, 561M, 561N, 613C II...
1283473
GEAR-PUMP DRIVE
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 950H, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 950H, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
3W5501
GEAR-PLANETARY
963, 963B, 963C
963, 963B, 963C
1764108
GEAR
953C, 963C
953C, 963C
1275009
GEAR
963C
963C
8Y6112
GEAR
963C
963C
8Y6112
GEAR
963C
963C
1745208
GEAR
953C, 963C, 973C
953C, 963C, 973C
1745207
GEAR
953C, 963C, 973C
953C, 963C, 973C
1275009
GEAR
963C
963C
5M7740
GEAR
977K, 977L, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL
977K, 977L, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL
9M2028
GEAR-SUN
572G, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
572G, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
1088555
GEAR
561H, 561M, 561N, PL61
561H, 561M, 561N, PL61
1065801
GEAR-SUN
561H, 561M, 561N, PL61
561H, 561M, 561N, PL61
1065800
GEAR-PLANETARY
561H, 561M, 561N, PL61
561H, 561M, 561N, PL61
1096934
GEAR-SPUR
933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
1096933
GEAR-PINION
933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
1276330
GEAR
963C
963C