GEAR-IDLER 1304700 - Caterpillar

1304700 GEAR-IDLER Caterpillar parts

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1304700
130-4700
1304700

Buy GEAR-IDLER 1304700 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices:

As an associate, we earn commssions on qualifying purchases through the links below

MR. Snowplow Replaces BOSS HYD01603 1-1/2 X 10 INCH Angle Cylinder 1998-2005 V-Plow Buyers 1304700-

$189.99

14 Dec 2025
14.4005[6.48] pounds
US: Mr-Snowplow

MR. Snowplow Replaces BOSS HYD01603 1-1/2 X 10 INCH Angle Cylinder 1998-2005 V-Plow Buyers 1304700-
Mr. Snow Plow Qty.2 REPLACES BOSS HYD01603

EPR Distribution Power Angling Cylinder for Boss HYD01603 RT3 Smart Hitch 1.5x10 SA24 V-Plows

$124.99

17 Mar 2025

US: EPR Distributio

EPR Distribution Power Angling Cylinder for Boss HYD01603 RT3 Smart Hitch 1.5x10 SA24 V-Plows
EPR Distribution Replacement for Boss HYD01603 || Replacement for Buyers 1304700 || Compatible with Boss 1998-2005 V Plows

Qty.2 Replaces BOSS HYD01603 1-1/2 X 10 INCH Angle Cylinder 1998-2005 V-Plow Buyers 1304700-

$250.00

09 Feb 2025
14.4005[6.48] Pounds
US: Mr-Snowplow

Qty.2 Replaces BOSS HYD01603 1-1/2 X 10 INCH Angle Cylinder 1998-2005 V-Plow Buyers 1304700-
Mr. Snow Plow

Show more prices Caterpillar parts

For full view, you need register

Information:

Removal Procedure
Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
Illustration 1 g02138690
Typical Example
Disconnect fuel line (1) from both ends.
Illustration 2 g02140391
Typical Example
Disconnect solenoid harness (2) .
Illustration 3 g02139134
Remove bolts (3) from the manifold.
Illustration 4 g02139144
Remove manifold (4) .
Illustration 5 g02138698
Remove locknuts (5) .
Illustration 6 g02139150
Write down the polarity and remove wires (6) from the terminal studs. The polarity is designated by "+" and "-" signs around the terminal studs.
Illustration 7 g02139164
Remove seal (7) .
Illustration 8 g02139169
Remove pump assembly (8).
Illustration 9 g02167735
Remove backup rings (9), seal (10), and seal (11) from the pump assembly.Installation Procedure
Install the fuel priming pump in the reverse order of removal.
Illustration 10 g03381244
Proper orientation of the new fuel priming pump.
Use the pump seal installer that is provided in the pump kit to press in the pump assembly (8) and seals.Note: The outlet of the pump should be at the top center position.
Install new locknuts (6). Torque locknuts to 1.3 N m (12 lb in).
Torque bolts (3) to 12 3 N m (106 27 lb in).
Use two people in order to flush the fuel pump and fuel line (1) into a suitable container for disposal. The fuel pump can be activated by turning on the key or pressing the manual switch. The manual switch, if available, is located on the primary fuel filter base.