GEAR-SUN 1362881 - Caterpillar

1362881 GEAR-SUN Caterpillar parts 320 L, 345B, 345B L

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1362881
136-2881
1362881

Weight: 7 pounds 3 kg.

Buy GEAR-SUN 1362881 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$10.00

17 Aug 2021

US: # 1 Quality Par

RING - WEAR FOR HYSTER: 1362881
Parts Express HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || RING - WEAR. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY1362881 1362881 Â HYSTER 1362881 Â HYSTER1362881 1362881 Â Â . All Brand new & rebuilt items comes with 1 year warranty.

Number on catalog scheme: 12

Caterpillar 1362881 Parts scheme GEAR-SUN

For full view, you need register

Compatible equipment models: 1362881:

EXCAVATOR 320 L 345B 345B L Caterpillar

Information:

Illustration 1 g00895497This diagnostic code is associated with the power supply for the sensors. The FMI 04 means that the ECM has determined that the voltage of the sensor circuit is below normal.The possible causes of the diagnostic code are listed:
A sensor has failed.
The circuit is shorted to ground.
The ECM has failed. This is unlikely.Test Step 1. CHECK THE VOLTAGE AT THE ECM.
Turn the disconnect switch and the key start switch to the ON position.
Check the voltage at the harness connector for the ECM from contact J1-44 (wire X800-OR(Orange)) to contact J1-45 (J764-BR(Brown)). Use the 7X-1710 Cable probes to measure the voltage. Do NOT disconnect the machine harness from the ECM. Expected Result:The voltage is 8.0 0.5 DCV.Results:
OK - The voltage is 8.0 0.5 DCV. The sensor supply voltage is correct. Verify that the same diagnostic code is present. If the diagnostic code is still present the ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure, and perform this procedure again. If the failure is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The voltage is NOT 8.0 0.5 DCV. The voltage is less than 8.0 0.5 DCV. The sensor supply voltage is NOT correct. Proceed to Test Step 2.Test Step 2. CHECK FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the ECM.
At the harness connector for the ECM, measure the resistance between frame ground and contact J1-45 (wire J764-BR(Brown)). Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. Verify that the same diagnostic code is present. If the diagnostic code is still present the ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure, and perform this procedure again. If the failure is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - Resistance is less than 5 ohms. The machine harness has failed or a sensor has failed. Proceed to Test Step 3.Test Step 3. DISCONNECT THE SENSORS.
The key start switch and the disconnect switch remain in the OFF position.
One at a time, disconnect any sensor that uses the power supply from the machine harness.
After disconnecting each sensor, check the resistance from frame ground to contact J1-45 at the harness connector for the ECM. Expected Result:After disconnecting a particular sensor, the resistance changes and the resistance is greater than 5000 ohms.Results:
YES - After disconnecting a particular sensor, the resistance changes and the resistance is greater than 5000 ohms. The sensor that was just disconnected has failed.Repair: Replace the sensor.STOP
NO - After disconnecting all of the sensors, the resistance is less than 5 ohms. The machine harness is shorted to ground.Repair: Repair the machine harness or replace the machine harness. STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

345B and 345B L Excavators 4SS00001-UP (MACHINE)

114-1409: DRIVE GP-SWING » (21-TEETH) SEBP26930351

345B, 345B L & 345B LC Excavator 2SW00001-UP (MACHINE) POWERED BY 3176C Engine

114-1409: DRIVE GP-SWING » (21-TEETH) SEBP27540444

345B Excavator 2NW00001-UP (MACHINE) POWERED BY 3176C Engine

114-1409: DRIVE GP-SWING » (21-TEETH) SEBP28250304

Parts gear Caterpillar catalog:

7Y1430 GEAR-SUN
315C, 315D L, 318B, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 3...

7Y1631 GEAR-RING
318B, 320 L, 320B, 320N, OEMS

9T3408 GEAR
215B, 225, 231D, 320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 539, E300B, M325B

4I7464 GEAR-PLANETARY
322 FM L, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330D FM, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 34...

4I7466 GEAR-PLANETARY
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325...

4I7467 GEAR-RING
322 FM L, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330D FM, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 34...

1107216 GEAR-SUN
322 FM L, 322B L, 322B LN, 325B, 325B L, 330D FM, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 568 FM LL, M32...