AVSPARE.COM
parts catalog

GEAR 1500811 - Caterpillar


1500811 GEAR Caterpillar parts 303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E
Rating:
18
Alternative (cross code) number:
CA1500811
150-0811
1500811
Caterpillar 1500811 GEAR
Weight: 0.67 pounds 0 kg.

Buy GEAR 1500811 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$16.64

07 Jun 2024

US: guangxitengxian
Replacement For Compatible WithEngine Camshaft Seal ITM 15-00811
CUSDECOR
$15.34
 

30 Sep 2023
0.2[0.09] pounds
US: The Factory Dep
ITM Engine Components 15-00811 Engine Camshaft Seal
ITM Engine Components Fits: 1. 5L L4 1468cc 90 CID Hyundai Excel 1992-1994 Hyundai 1986-1991 Hyundai Scoupe 1991-1992 / 1. 5L L4 1495cc Hyundai Accent 2000-2002 Scoupe 1993-1995 / 1. 6L L4 1596cc Hyundai Elantra 1992-1995 / 1. 6L L4 1599cc Hyundai Accent 2006-2011 / 1. 6L L4 1600cc 2001-2006 /1. 8L L4 1975cc Hyundai Elantra 1996-1997 Hyundai Tiburon 1997 /1. 8L L4 1976cc Hyundai Elantra 1998 / 1. 8L L4 1836cc Hyundai Elantra 1993-1994 / 1. 8L L4 1836cc Hyundai Elantra 1995 / 2. 0L L4 1975cc Hyundai Elantra 1999-2009 Hyundai Tiburon 1997, 2003-2008 Hyundai Tucson 2005-2009 Kia Spectra 2004-2009 / 2. 0L L4 1997cc Hyundai Sonata 1992-1998 Hyundai Tiburon 1998-2001 / 2. 4L L4 2351cc Hyundai Santa Fe 2001-2004 Hyundai Sonata 1989-2005 Kia Optima 2001-2006 Mitsubishi Galant 1994-2003 / 3. 0L V6 2972cc 181 CID Mitsubishi Ecliose 2000-2005 || High quality aluminum, cast iron, and plastics are used for durability and reliability || Featuring state of the art manufacturing technology and premium materials. || non-asbestos materials are used to meet modern environmental standards. || Quality OE replacements at a great value.
$29.68
 

14 Jun 2023

US: Yurafilipon
Engine Camshaft Seal-DOHC ITM 15-00811 Model-XGFT-6417
Generic Part Number: 15-00811; Type: Engine Camshaft Seal; OE/OEM Part Number: 2214433004,35X60X10SCR2,710424,CS19304356010,S99772;
Number on catalog scheme: 7
  For full view, you need register

Compatible equipment models: 1500811:

MINI HYD EXCAVATOR  303   303.5C   303.5D   303.5E   303C CR   303E CR   304D CR   304E   Caterpillar

Information:

Introduction
The following will explain the procedure for purging the steering system.Required Tools
Table 1
Tool Part Number Description Qty
D 8T-2362 Adapter(1) 4
7J-0204 O-Ring Seal 4
6V-8628 Elbow 4
3J-7354 O-Ring Seal 4
4J-5477 O-Ring Seal 4
9C-2394 Hose As 2
F 6V-3668 Bolt 2
5P-8245 Hard Washer 8
(1) The adapter must be change 02. Exterior thread is 3/8 by 24. Interior threads are 7/16 by 20.Machine Preparation
Move the machine to a smooth horizontal location.
Chock the wheels.
Lower all of the implements.
Illustration 1 g01459671
Steering cylinders
Install bolts and washers (F) onto the locations (1) and (2) that are called out on the front axle body. Note: Be careful not to engage the wheel lean. This could result in damage to Tool (F).
Illustration 2 g01459676
Typical top view of front axle
(1) Steering cylinders
(2) Plugs
Remove plugs (2) from each steering cylinder (1).
Use the parts that are listed in Table 1 in order to connect the port of the rod end to the port of the head end. Perform this procedure for both of the cylinders. Purge Procedure (Steering System)
Start the engine and operate the engine at low idle.
Align the left hand joystick control so that the joystick control will match the steering angle of the front wheels.
Move the left hand joystick control all the way to the left and hold for 30 seconds.
Move the left hand joystick control all the way to the right and hold for 30 seconds.
Shut off the engine.
Remove the parts that are listed in Table 1 from locations (1) and (2).
Check the oil level in the hydraulic tank. Purge Procedure (Signal Network)
Reference: Before you perform this procedure, refer to Testing and Adjusting, "Machine Preparation for Troubleshooting".Note: Perform the Steering System−Purge procedures before you perform the purge procedure for the signal network.
Illustration 3 g01298276
Pump control valve
(3) Purge valve for flow compensator
Use a hex wrench. Turn purge valve (3) counterclockwise by one turn in order to open the valve.
Start the engine and operate the engine at low idle. During this procedure, a small amount of oil may leak by the purge valve.
The implement lockout switch must be in the unlocked position.
Select an implement.
Move the joystick control in order to extend the implement cylinder. Hold the joystick control in this position for ten seconds.
Move the joystick control in order to retract the implement cylinder. Hold the joystick control in this position for ten seconds.
Repeat for each implement circuit on the machine.
Turn purge valve (3) clockwise in order to close the valve.
Stop the engine.

Caterpillar parts catalog:

Caterpillar parts catalog
303ECR Mini Hydraulic Excavator CK300001-UP (MACHINE) POWERED BY C1.3 Engine
303 CR Mini Hydraulic Excavator DMA00001-UP (MACHINE) POWERED BY S3L2 Engine
304D CR Mini Excavator TYK00001-UP (MACHINE) POWERED BY S3Q2 Engine
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY S3Q2 Engine
303C CR Mini Hydraulic Excavator BXT00001-UP (MACHINE) POWERED BY S3Q2 Engine
303.5 D Mini Excavator RHP00001-UP (MACHINE) POWERED BY S3Q2 Engine
303.5E Mini Hydraulic Excavator RKY00001-UP (MACHINE) POWERED BY C1.8 Engine
304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1.3 Engine
303.5E Mini Hydraulic Excavator SFH00001-UP (MACHINE)
303.5E Mini Hydraulic Excavator RSE00001-UP (MACHINE)
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)
304E Mini Hydraulic Excavator TSR00001-UP (MACHINE)
303E CR Mini Hydraulic Excavator CR700001-UP (MACHINE) POWERED BY C1.3 Engine
303E CR Mini Hydraulic Excavator HHM00001-UP (MACHINE) POWERED BY C1.3 Engine
303E CR Mini Hydraulic Excavator SGE00001-UP (MACHINE) POWERED BY C1.3 Engine


Parts gear Caterpillar catalog:

3830401 GEAR-IDLER
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830399 GEAR-CRANKSHAFT
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830420 GEAR-RING
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830558 GEAR
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830341 GEAR-PUMP
304E, 305.5E, 305E, 902C, 903C
1992348 GEAR AS
302.5C, 303, 304
1968385 GEAR AS
302.5C, 303, 304
1992217 GEAR AS
302.5C, 303, 304
1500815 GEAR
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.