1P3187 GEAR ASSEM. (53 teeth) Caterpillar parts
950
Rating:
Alternative (cross code) number:
CA1P3187
1P-3187
1P3187
CA1P3187
1P-3187
1P3187
Weight: 36 pounds 16 kg.
WHEEL LOADER,
Compatible equipment models: 1P3187:
Number on catalog scheme:
6
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
(M8 by 70 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear or damage. If necessary, replace the water pump.
Illustration 1 g01336659
If necessary, install cover (6) to water pump (3). Follow Steps 2.a through 2.d in order to install the cover.
Clean the mating surface of cover (6).
Position a new joint (5) on water pump (3).
Install cover (6) to water pump (3).
Install bolts (7) to cover (6). Tighten bolts finger tight.
Clean the mating surface of front cover (1).
Illustration 2 g01336660
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new joint (2) to front cover (1). Install the joint to the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Install bolts (4). Refer to Illustration 1. Tighten the bolts finger tight. Note: Ensure that all bolts of different lengths are installed in the correct positions.
Remove Tooling (A) and install remaining bolts (4).
Illustration 3 g01336661
Tighten bolts (4) and (7) in the sequence that is shown in Illustration 3 to a torque of 22 N m (16 lb ft).
Install the hose to the water pump inlet. Tighten the hose clamps.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
(M8 by 70 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear or damage. If necessary, replace the water pump.
Illustration 1 g01336659
If necessary, install cover (6) to water pump (3). Follow Steps 2.a through 2.d in order to install the cover.
Clean the mating surface of cover (6).
Position a new joint (5) on water pump (3).
Install cover (6) to water pump (3).
Install bolts (7) to cover (6). Tighten bolts finger tight.
Clean the mating surface of front cover (1).
Illustration 2 g01336660
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new joint (2) to front cover (1). Install the joint to the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Install bolts (4). Refer to Illustration 1. Tighten the bolts finger tight. Note: Ensure that all bolts of different lengths are installed in the correct positions.
Remove Tooling (A) and install remaining bolts (4).
Illustration 3 g01336661
Tighten bolts (4) and (7) in the sequence that is shown in Illustration 3 to a torque of 22 N m (16 lb ft).
Install the hose to the water pump inlet. Tighten the hose clamps.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 225, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 330B L, 350,...
814, 815, 950, 955K, 955L, 966C, D5, D5B
814, 815, 950, 955K, 955L, 966C, D5, D5B
814, 950, 955K, 955L, 966C, D5, D5B
814, 950, 955K, 955L, 966C, D5, D5B
814, 950, 955K, 955L, 966C, D5, D5B
518, 613, 613B, 815, 950, 966C
613, 613B, 950
518, 920, 930, 950
518, 920, 930, 950
613, 613B, 950
814, 816, 950, 966C
528, 814, 815, 966C
9K5485
GEAR (35 Teeth)
814, 950, 966C
814, 950, 966C
7K9563
GEAR (45 Teeth)
834, 992
834, 992
1P0981
GEAR (8 Teeth)
824B, 992
824B, 992
1V6422
GEAR
834, 992
834, 992
6A8703
GEAR (9 teeth)
950, 966C
950, 966C
6A7277
GEAR (16 teeth)
950, 966C
950, 966C
815, 966C