1P9641 GEAR ASSEM. (12 Teeth) Caterpillar parts
14E
Rating:
Alternative (cross code) number:
CA1P9641
1P-9641
1P9641
CA1P9641
1P-9641
1P9641
MOTOR GRADER,
Compatible equipment models: 1P9641:
Number on catalog scheme:
9
For full view, you need register
Information:
Removal Procedure
The Power Train Electric Drive System will contain hazardous voltage levels during machine operation and for a short period of time after engine shutdown.Do not remove any covers that will expose energized high voltage electrical components while the engine is operating.Any type of maintenance on the following components can only be performed after the Power Train Electrical System Service Shutdown procedure has been followed:
High voltage compartments in the inverter cabinet
The rear axle housing that contains the electric drive traction motors
The generator
The retarding resistor grid, the grid blower motor and the grid system cabling
The excitation field regulator
The high voltage cables and connection enclosuresFailure to follow these instructions could result in personal injury or death.
The two top compartments on the front of the Inverter Cabinet contain low voltage control components. All of the other compartments in the cabinet contain high voltage components. The "Electrical Shutdown and Voltage Discharge" procedure must be performed before any of the high voltage compartments are entered.
Refer to Operation and Maintenance Manual, "Electrical Shutdown and Voltage Discharge".
Refer to Operation and Maintenance Manual, "Prepare the Machine for Maintenance".
Illustration 1 g03478241
Remove panel (1).
Illustration 2 g03478247
Disconnect cable assemblies (2) and harness assembly (3).
Remove bolts (4). Remove interface module (5). Installation Procedure
Install interface module (5) in the reverse order of removal.
The Power Train Electric Drive System will contain hazardous voltage levels during machine operation and for a short period of time after engine shutdown.Do not remove any covers that will expose energized high voltage electrical components while the engine is operating.Any type of maintenance on the following components can only be performed after the Power Train Electrical System Service Shutdown procedure has been followed:
High voltage compartments in the inverter cabinet
The rear axle housing that contains the electric drive traction motors
The generator
The retarding resistor grid, the grid blower motor and the grid system cabling
The excitation field regulator
The high voltage cables and connection enclosuresFailure to follow these instructions could result in personal injury or death.
The two top compartments on the front of the Inverter Cabinet contain low voltage control components. All of the other compartments in the cabinet contain high voltage components. The "Electrical Shutdown and Voltage Discharge" procedure must be performed before any of the high voltage compartments are entered.
Refer to Operation and Maintenance Manual, "Electrical Shutdown and Voltage Discharge".
Refer to Operation and Maintenance Manual, "Prepare the Machine for Maintenance".
Illustration 1 g03478241
Remove panel (1).
Illustration 2 g03478247
Disconnect cable assemblies (2) and harness assembly (3).
Remove bolts (4). Remove interface module (5). Installation Procedure
Install interface module (5) in the reverse order of removal.
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
12F, 14E
12F, 140B, 14E, 1673C, D6C
14E, 572G, 627, 627B, 637B, 637D, 977K, 977L, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2
14E, 572G, D7G, D7G2
120B, 12E, 12F, 140, 140B, 14E
120B, 12E, 12F, 140, 140B, 14E
12F, 140, 14E
120B, 12E, 12F, 140, 140B, 14E
12F, 14E
120B, 12E, 12F, 140, 140B, 14E
120B, 12E, 12F, 140, 140B, 14E
120B, 12E, 14E
6D8203
GEAR
12F
12F
6D4677
GEAR ASSEM. (38 Teeth)
14E, 16
14E, 16
9J2927
GEAR SET
16G
16G
6D3883
GEAR (24 Teeth)
12F, 12G, 14E, 16, 16G
12F, 12G, 14E, 16, 16G
6D3923
GEAR (32 Teeth)
12F, 16
12F, 16