2D7619 GEAR Caterpillar parts
140B, 14E
Rating:
Alternative (cross code) number:
CA2D7619
2D-7619
2D7619
CA2D7619
2D-7619
2D7619
Weight: 12 pounds 5 kg.
MOTOR GRADER,
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Bracket As 2
B 421-5662 Lifting Eye Assembly 2 Start By:
Connect the steering frame lock.
Release the hydraulic system pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03723117
Remove covers (1) and (2).
Illustration 2 g03723120
Attach Tooling (A) and a suitable lifting device to cover assembly (3). The weight of cover assembly (3) is approximately 74 kg (163 lb).
Remove bolts (4) and the washers.
Illustration 3 g03723148
Remove bolts (5) and the washers. Remove bolt (6) (not shown) and the washer. Repeat this step for the opposite side of cover assembly (3).
Use Tooling (A) and the suitable lifting device in order to remove cover assembly (3).
Illustration 4 g03723179
Disconnect hose assemblies (7).
Disconnect tube assemblies (8).
Illustration 5 g03723199
Disconnect hose assemblies (9).
Remove tube assemblies (10).
Illustration 6 g03723239
Remove fittings (11).
Disconnect harness assemblies (12). Cut the cable straps.
Illustration 7 g03723291
Attach Tooling (B) and a suitable lifting device to main control valve (13). The weight of main control valve (13) is approximately 38 kg (84 lb).
Remove bolts (14) and the washers. Remove bolts (15) and the washers. Use Tooling (B) and the suitable lifting device in order to remove main control valve (13). Installation Procedure
Install main control valve (13) in the reverse order of removal.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Bracket As 2
B 421-5662 Lifting Eye Assembly 2 Start By:
Connect the steering frame lock.
Release the hydraulic system pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03723117
Remove covers (1) and (2).
Illustration 2 g03723120
Attach Tooling (A) and a suitable lifting device to cover assembly (3). The weight of cover assembly (3) is approximately 74 kg (163 lb).
Remove bolts (4) and the washers.
Illustration 3 g03723148
Remove bolts (5) and the washers. Remove bolt (6) (not shown) and the washer. Repeat this step for the opposite side of cover assembly (3).
Use Tooling (A) and the suitable lifting device in order to remove cover assembly (3).
Illustration 4 g03723179
Disconnect hose assemblies (7).
Disconnect tube assemblies (8).
Illustration 5 g03723199
Disconnect hose assemblies (9).
Remove tube assemblies (10).
Illustration 6 g03723239
Remove fittings (11).
Disconnect harness assemblies (12). Cut the cable straps.
Illustration 7 g03723291
Attach Tooling (B) and a suitable lifting device to main control valve (13). The weight of main control valve (13) is approximately 38 kg (84 lb).
Remove bolts (14) and the washers. Remove bolts (15) and the washers. Use Tooling (B) and the suitable lifting device in order to remove main control valve (13). Installation Procedure
Install main control valve (13) in the reverse order of removal.
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
12F, 14E
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 330, 330 L, 3304, 3304B, 3306, 3306B, 350, 515, 517, 518...
140B, 235, 330, 330 L, 3304, 3304B, 3306, 3306B, 350, 515, 517, 525, 527, 561D, 627E, 627F, 637E, 65C, 963, 966F, 966F II, 970F, 972G, 973, CB-534, D4H, D4H XL, D4HTSK III, D5E, D5H, D5H XL, D5HTSK II...
14E, 941, 966C, 977K, D6C, D7F
120B, 12E, 140, 140B
120B, 140B
12F, 140, 140B, 14E
120B, 12E, 12F, 140, 140B, 14E
120B, 140B
120B, 12E, 12F, 140, 140B, 14E
12F, 14E
12F, 14E
120B, 12E, 14E
120B, 12E, 14E
6D8286
GEAR ASSEM. (41 Teeth)
12F, 14E
12F, 14E
7D4847
GEAR (13 Teeth)
12F, 14E
12F, 14E
2D7618
GEAR
140B, 14E
140B, 14E