GEAR ASSEMBLY 2L9419 - Caterpillar

Install Tooling (D) onto the special studs (AA) on both sides of adapter assembly (3). Tighten Tooling (D) appropriately to equalize the gaps between the upper and lower adapter assemblies.
Illustration 20 g03847821
(1) 147-0170 Bolt
(2) 146-1799 Hard Washer
(3) 282-6634 Adapter
(C) 443-7797 Tool Gp 443-7801 Tool Gp
(B) 439-3943 Link Bracket
(D) 8C-3226 Bolt 6V-8149 Nut 5P-8245 Hard Washer
Once the gaps on each side of the adapters are equalized, use Tooling (C) to tighten all bolts (1) to a torque of 3100 350 N m (2290 260 lb ft).
Remove Tooling (B), Tooling (D), and the lifting devices.
Illustration 21 g03889698
(4) Tire and Rim Assembly
The weight of the tire and rim can vary significantly depending on the tire and rim configuration
Use a suitable tire handler to position the outer tire and rim assembly (4) onto the wheel. The weight of tire and rim (4) is approximately 8618 kg (19000 lb).Note: The valve stem must face outward.
Illustration 22 g03847859
(4) Tire and Rim Assembly
(5) 146-1799 Hard Washer
(6) 8C-4032 Nut
(C) 443-7797 Tool Gp 443-7801 Tool Gp 159-2833 Socket
Apply Tooling (E) or a light coat of oil onto the wheel studs after the wheel has been fully seated to avoid contamination of the mating surfaces. Anti-seize may be preferred in corrosive environments to make nut removal easier when removing rims. No other anti-seize compound is to be used.
Apply Tooling (E) or a light coat of oil onto four of the wheel studs that are equally spaced and approximately 90 degrees apart. Install four nuts (6) and four washers (5) to secure tire and rim (4) onto the wheel.
Apply Tooling (E) or a light coat of oil onto the remaining wheel studs.
Install the remaining nuts (6) and washers (5). Use Tooling (C) to tighten nuts (6) to a torque of 3100 350 N m (2286 258 lb ft).Note: Apply a light coat of oil to the faces of the washers.
Illustration 23 g03848549
(10) 3W-1100 Spacer
(11) 203-4705 Plate
(12) 8T-4223 Hard Washer
(13) 8T-4910 Bolt
(14) 203-4703 Adapter
(16) 203-4702 Valve
(17) 146-4279 Cap
Install adapter (14), valve (16), and cap (17).
Install plate (11), two spacers (10), two hard washers (12), and two bolts (13).
Illustration 24 g03848857
(16) 203-4702 Valve
(17) 146-4279 Cap
(18) 201-6654 Hose As
(19) 6V-8990 Elbow
(20) 2P-1293 Locknut
(21) 6V-9746 O-Ring Seal
Install adapter (19) onto hose assembly (18). Install valve (16), cap (17), locknut (20), and two O-rings (21).
Illustration 25 g03887441
Outboard side of outer tire and rim assembly
(22) 220-7281 Plate
(23) 8T-4122 Hard Washer
(24) 8T-4779 Bolt
Install three plates (22), three hard washers (23), and three bolts (24).
Repeat Step 4 through Step 25 for the opposite side rear wheels.