2S0622 GEAR (46 Teeth) Caterpillar parts
950
Rating:
Alternative (cross code) number:
CA2S0622
2S-0622
2S0622
CA2S0622
2S-0622
2S0622
Weight: 3 pounds 1 kg.
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$96.12
22 Jun 2022
US: Florida-Parts-Z
2S0622 - Gear (46 Teeth) fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$85.33
22 Jun 2022
US: QUALITY PARTS
Made to fit 2S0622 Gear Caterpillar
G&T Engine Parts 2S0622 Caterpillar Gear || Meets OEM Specs for Fit and Performance || This is a new item 2S0622 Gear Caterpillar || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts 2S0622 Caterpillar Gear || Meets OEM Specs for Fit and Performance || This is a new item 2S0622 Gear Caterpillar || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
$85.90
22 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Gear 2S0622 New
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 2S0622:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6080 Torque Multiplier 1
5P-1748 Socket 1
4C-9451 Rear Idler Gear Wrench 1
4C-9452 Rear Idler Gear Wrench 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611176
Illustration 2 g00611187
If the bearing was removed from gear (8) , install the bearing in the gear. The bearing must be located at a distance of 2.50 0.50 mm (0.10 0.020 inch) below the surface of the side of the gear. This distance is measured on the gear with the smaller shoulder. The inside diameter of the gear should be 124.980 0.020 mm (4.9210 0.0008 inch) after installation.
Put gear (10) in position on gear (8) . Install bolts (6) .
Put the following components in position on shaft (5) : gear (8) and other gear (10) . Install bolts (9) . Do not tighten the bolts at this time.
Attach a suitable lifting device to gear (10) . Put gear (10) and shaft (5) in position in the rear housing through the opening for the camshaft drive gear.
Fasten a hoist to the gear (10) through the opening in the rear housing. This opening is for the accessory drive. Remove the hoist through the opening of the drive gear.
Align the teeth on gear (10) with the teeth on gear (12) . Put shaft (5) in position on the cylinder block. Install four bolts (11) . Tighten the bolts to a torque of 200 25 N m (150 18 lb ft).
Tighten bolts (9) .
If the bearings were removed from gears (2) , install the bearings in the gears. The bearings must be 2.5 0.5 mm (0.098 0.02 inch) below the flat surface of the gear. The inside diameter of the bearings should be 150.002 0.020 mm (5.9056 0.0008 inch) after installation.
Put gear (2) and retainer (4) in position on shaft (3) . Install the bolts that hold these components in place.
Attach a suitable lifting device to gear (2) . Put the gear and the shaft in position on the cylinder block through the opening for the camshaft drive gear in the rear housing. Install four bolts (1) . Tighten the bolts to a torque of 475 50 N m (350 37 lb ft).
Repeat Step 9 and Step 10 for the other idler gear.
Illustration 3 g00664018
Note: The center lobe of the camshaft segment on the G3612 and the G3616 Engine is narrower than the center lobe on the 3612 or the 3616 Diesel Engine.
Put spacer (14) in position on the end of drive shaft (13) .
Align the dowel in shaft (13) with the dowel hole in camshaft segment (16) . Install bolts (15) . Tighten all of bolts (15) by hand.
Illustration 4 g00611192
Put plate (20) in position
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6080 Torque Multiplier 1
5P-1748 Socket 1
4C-9451 Rear Idler Gear Wrench 1
4C-9452 Rear Idler Gear Wrench 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611176
Illustration 2 g00611187
If the bearing was removed from gear (8) , install the bearing in the gear. The bearing must be located at a distance of 2.50 0.50 mm (0.10 0.020 inch) below the surface of the side of the gear. This distance is measured on the gear with the smaller shoulder. The inside diameter of the gear should be 124.980 0.020 mm (4.9210 0.0008 inch) after installation.
Put gear (10) in position on gear (8) . Install bolts (6) .
Put the following components in position on shaft (5) : gear (8) and other gear (10) . Install bolts (9) . Do not tighten the bolts at this time.
Attach a suitable lifting device to gear (10) . Put gear (10) and shaft (5) in position in the rear housing through the opening for the camshaft drive gear.
Fasten a hoist to the gear (10) through the opening in the rear housing. This opening is for the accessory drive. Remove the hoist through the opening of the drive gear.
Align the teeth on gear (10) with the teeth on gear (12) . Put shaft (5) in position on the cylinder block. Install four bolts (11) . Tighten the bolts to a torque of 200 25 N m (150 18 lb ft).
Tighten bolts (9) .
If the bearings were removed from gears (2) , install the bearings in the gears. The bearings must be 2.5 0.5 mm (0.098 0.02 inch) below the flat surface of the gear. The inside diameter of the bearings should be 150.002 0.020 mm (5.9056 0.0008 inch) after installation.
Put gear (2) and retainer (4) in position on shaft (3) . Install the bolts that hold these components in place.
Attach a suitable lifting device to gear (2) . Put the gear and the shaft in position on the cylinder block through the opening for the camshaft drive gear in the rear housing. Install four bolts (1) . Tighten the bolts to a torque of 475 50 N m (350 37 lb ft).
Repeat Step 9 and Step 10 for the other idler gear.
Illustration 3 g00664018
Note: The center lobe of the camshaft segment on the G3612 and the G3616 Engine is narrower than the center lobe on the 3612 or the 3616 Diesel Engine.
Put spacer (14) in position on the end of drive shaft (13) .
Align the dowel in shaft (13) with the dowel hole in camshaft segment (16) . Install bolts (15) . Tighten all of bolts (15) by hand.
Illustration 4 g00611192
Put plate (20) in position
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 225, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 330B L, 350,...
814, 815, 950, 955K, 955L, 966C, D5, D5B
814, 815, 950, 955K, 955L, 966C, D5, D5B
814, 950, 955K, 955L, 966C, D5, D5B
814, 950, 955K, 955L, 966C, D5, D5B
814, 950, 955K, 955L, 966C, D5, D5B
518, 613, 613B, 815, 950, 966C
613, 613B, 950
518, 920, 930, 950
518, 920, 930, 950
613, 613B, 950
814, 816, 950, 966C
1S5283
GEAR (24 Teeth)
824B, 825B, 980, 980B, 988
824B, 825B, 980, 980B, 988
16, 824B, 825B, 988
9S2808
GEAR ASSEM. (32 and 37 Teeth)
824B, 825B, 988
824B, 825B, 988
16, 824B, 825B, 988
2M7090
GEAR (21 Teeth)
16, 824B, 825B, 988
16, 824B, 825B, 988
4M7128
GEAR (124 and 80 Teeth)
16, 824B, 825B, 988
16, 824B, 825B, 988
16, 824B, 825B, 988