AVSPARE.COM
parts catalog

GEAR-RING 4826735 - Caterpillar


4826735 GEAR-RING Caterpillar parts
Rating:
31
Alternative (cross code) number:
CA4826735
482-6735
4826735
Caterpillar 4826735 GEAR-RING
Weight: 21 pounds 9 kg.

Buy GEAR-RING 4826735 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 7
  For full view, you need register

Information:


Do not connect or disconnect hose fittings to or from the quick disconnect nipples when there is pressure in the system. This will prevent damage to the seals that are in the fitting.
Illustration 5 g00107976
Outlet relief valve
(11) Torque converter outlet relief valve
(17) Spacers
Table 1
Torque Converter Pressure
Pressure Pressure Tap Pressure at High Idle Adjustment
Lockup Clutch Hold Pressure (If equipped) (C) Minimum pressure is: 1965 kPa (285 psi)
Maximum pressure is: 2100 kPa (305 psi) -
Torque Converter Inlet (D) Maximum pressure with cold oil is 930 kPa (135 psi). -
Impeller Clutch (Pedal Released) (F) Impeller clutch pressure is 1980 300 kPa (285 44 psi). -
Impeller Clutch (Pedal Depressed) Minimum pressure is 356 kPa (50 psi).
Maximum pressure is 657 kPa (95 psi). -
Torque Converter Outlet (H) Torque converter outlet pressure is: 483 68 kPa (70 10 psi). Add spacers (17) or remove spacers (17).
Table 2
Pressure Change for One Spacer(1)
Description Thickness Pressure Change Part
5M-9623 Spacer 0.91 mm (0.036 inch) 18.2 kPa (2.64 psi) Output Relief Valve (11)
5M-9624 Spacer 0.25 mm (0.010 inch) 5.0 kPa (0.73 psi)
(1) Before an adjustment is made to outlet relief valve (11), make sure that the valve springs are not weak or broken.
Table 3
Required Tools
Part Number Description Quantity
1U-5481 Pressure Gauge Group 1
1U-5482 Pressure Gauge Group 1 Maximum and Minimum Clutch Pressure
The drive shaft rotates between the torque converter and the transmission whenever the engine is running. Contact with the rotating shaft can result in personal injury or death.The rotating shaft is located under the implement and steering pumps. Do not allow personnel into the pump bay area behind the cab when the engine is running.
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before moving the machine to perform the test that follows.
Note: Make sure that the left service brake pedal position sensor is calibrated correctly before you perform the pressure tests. The test values can be affected if the left service brake pedal position sensor is not calibrated correctly.Reference: Refer to the Service Manual module for Systems Operation, Testing, and Adjusting, "Position Sensor (Left Brake Pedal) (Operator Monitor) - Calibrate" or Systems Operation, Testing, and Adjusting, "Position Sensor (Left Brake Pedal) (Electronic Technician) - Calibrate" for the calibration procedure for the

Caterpillar parts catalog:

Caterpillar parts catalog
416F2 Center Pivot Backhoe Loader LBF00001-UP (MACHINE) POWERED BY 3054C, C4.4 Engine
420F2 Center Pivot Backhoe Loader LBS00001-UP (MACHINE) POWERED BY 3054C, C4.4 Engine
918M Compact Wheel Loader H2600001-UP (MACHINE) POWERED BY C4.4 Engine
920K Compact Wheel Loader B9800001-UP (MACHINE) POWERED BY C4.4B Engine


Parts gear Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.