4N3851 GEAR Caterpillar parts
3406
Rating:
Alternative (cross code) number:
CA4N3851
4N-3851
4N3851
CA4N3851
4N-3851
4N3851
Weight: 0.05 pounds 0 kg.
INDUSTRIAL ENGINE, TRUCK ENGINE,
Compatible equipment models: 4N3851:
Information:
Illustration 16 g03358209
Select the manual speed deactivation value. This feature disables manual operation of the system when machine speed is greater than the deactivation value. Note: This feature can be used at work sites that desire system operation to be disabled while operating at road speeds.
Illustration 17 g03358212
Select the "Intermittent Mode Enable" option in the "SetUp" menu. Press "OK" button (E) .
Illustration 18 g03358213
Scroll down and select the "Enabled" option. Press "OK" button (E) .
Illustration 19 g03358214
If the PIN code needs to be changed, select the "Config Change PIN code" option in the "SetUp" menu. Press "OK" button (E) .Spray Head Calibration
Note: The machine should be at an operating temperature of 65 °C (149 °F) before performing this calibration procedure.Note: The main display can be used to monitor hydraulic temperatures. Press the" F2" button to open the "Measure" menu. Scroll down and select the "WDS Hyd Tank & Fan" option in order to monitor hydraulic temperatures.Note: This calibration procedure will require spraying up to a half tank of water. Perform this procedure in a location that can accommodate spraying. Ensure that adequate water supplies are in the water tank before commencing the calibration.Note: If the spray is uneven after calibration, small adjustments can be made to even out the spray pattern.
Illustration 20 g03522458
In the "Main" display screen, press "F1" button (A) to select the "Adjust" menu.
Illustration 21 g03522459
In the "Adjust" screen, scroll down and press "OK" button (E) to select the "Spray Head Calibration" menu.
Illustration 22 g03522460
Enter the PIN code. Use "up" button (F) and "down" button (D) to select a digit. Use "back" button (G) to delete a digit. Use "OK" button (E) to enter the digit.
Illustration 23 g03522461
Scroll down and select the "2-5 Spray Head Calibration" option. Press "OK" button (E) .Note: The "167 Spray Head Calibration" option is performed for the auxiliary spray head options. This calibration does not affect water coverage but can be used to obtain a more consistent spray.
Illustration 24 g03522462
Scroll down and select the "Enable" option. Press "OK" button (E). Press "back" button (G) to exit the screen.
Illustration 25 g03522464
The calibration screen allows the operator to activate one spray head at a time and calibrate individual spray heads. Activate the WDS pump. Once the water is activated, push the accelerator to the floor to achieve the target speed of 2000 rpm. Once the target speed is met, the light will turn green. Water pressure should automatically settle to a pressure of 551 kPa (80 psi) 80 psi if the system is working correctly. The light will turn green. Calibrate individual spray heads by pressing corresponding function key (H) below the head being calibrated.
Illustration 26 g03522465
When calibrating an individual spray head, adjust the value for head intensity. If hydraulic pressure is low, increase the head intensity. If hydraulic pressure is high, decrease the head intensity value. After adjusting the value for head intensity, press the OK button to return to the calibration screen. Check hydraulic pressure. If pressure is within 50 psi of the target pressure, the light will turn green. Continue
Cat SIS web machinery list:
Parts gear Caterpillar catalog:
4N4394
GEAR-DRIVE
3176B, 3176C, 3196, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3456, 768B, 769, C-10, C-12, C-15, C-16, C-9, C11, C12, C13, C15, C18, C7, C9, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX35-C18I, ...
3176B, 3176C, 3196, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3456, 768B, 769, C-10, C-12, C-15, C-16, C-9, C11, C12, C13, C15, C18, C7, C9, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX35-C18I, ...
9G6458
GEAR
3406, 3406B, 3408
3406, 3406B, 3408
9G6457
GEAR
3406, 3406B, 3408
3406, 3406B, 3408
2L1760
GEAR-COUNTERSHAFT
3406, 3408, D337F, D342, D342C, D343
3406, 3408, D337F, D342, D342C, D343
3N4821
GEAR-OUTPUT
3406, 3406B, 3408, D343
3406, 3406B, 3408, D343
6L6374
GEAR (42 Teeth)
3306, 3406, D333A, D333B, D334
3306, 3406, D333A, D333B, D334
6L6371
GEAR (48 Teeth)
3406, 3406B, D333B, D334
3406, 3406B, D333B, D334
6L6375
GEAR (42 Teeth)
3306, 3406, D333A, D333B, D334
3306, 3406, D333A, D333B, D334
6L8349
GEAR-DRIVE
3406, D333A
3406, D333A
5L6570
GEAR (27 TEETH)
3406, D342, D342C, D343
3406, D342, D342C, D343
5L4100
GEAR (DRIVER)
3406, D342, D342C
3406, D342, D342C
5L5797
GEAR (126 TEETH)
3406, 3408, D343
3406, 3408, D343
2P0659
GEAR ASSEM. (40 teeth)
120G, 1673C, 3304, 3306, 814, 920, 930, 950, D4D, D7G
120G, 1673C, 3304, 3306, 814, 920, 930, 950, D4D, D7G
2P2546
GEAR (8 Teeth)
3304, 3306, 955L, D4D, D5, D6C
3304, 3306, 955L, D4D, D5, D6C
4N3330
GEAR (80 Teeth)
120B, 120G, 140B, 225, 910, 920, 931B, 950, D3, D4D, D6C, G3304
120B, 120G, 140B, 225, 910, 920, 931B, 950, D3, D4D, D6C, G3304
2P1172
GEAR ASSEM. (60 Teeth)
120B, 120G, 140B, 1673C, 225, 330 L, 3304, 3306, 572G, 637D, 920, 936F, 950, 955L, 963, 970F, D4D, D5, D5H, D6C, D6D, D6H, D7G, D7H, G3304
120B, 120G, 140B, 1673C, 225, 330 L, 3304, 3306, 572G, 637D, 920, 936F, 950, 955L, 963, 970F, D4D, D5, D5H, D6C, D6D, D6H, D7G, D7H, G3304
3N1345
GEAR ASSEM.
G399
G399
9F9598
GEAR ASSEM. (15 Teeth)
D342, D342C, D348, D349, D353C, G399
D342, D342C, D348, D349, D353C, G399
5L9146
GEAR (40 Teeth)
1693, D343
1693, D343
5L8850
GEAR ASSEM. (55 Teeth)
1693, 631C, 988, D343, G343
1693, 631C, 988, D343, G343
8H9226
GEAR (46 TEETH)
12E, 955H, D320A, D330A, D333A, D4D
12E, 955H, D320A, D330A, D333A, D4D
8H7197
GEAR (36 Teeth)
955C, D342, D342C, D353C
955C, D342, D342C, D353C
8H5198
GEAR (11 Teeth)
D353C, D9E, D9G
D353C, D9E, D9G
4S7863
GEAR (40 TEETH)
D342, D342C, D8H, D8K, G342C
D342, D342C, D8H, D8K, G342C