GEAR-BEVEL 4V5393 - Caterpillar

4V5393 GEAR-BEVEL Caterpillar parts 815B, 816B, 966D

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4V5393
4V-5393
4V5393

Weight: 42 pounds 19 kg.

Buy GEAR-BEVEL 4V5393 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR, WHEEL LOADER,

Related part:

4V5393 GEAR-BEVEL-YM 2977189 CL

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

4V5393 Gear-Bevel CGR Ghinassi - Made in Italy

$431.91

14 Nov 2021

Amazon.com

4V5393 Gear-Bevel CGR Ghinassi - Made in Italy
CGR Compatible Models - 815B 816B 814B 966D || Related Items - 0300060 0300061 5M7329 3J0634 2K5109 5K2595 5L2031 5L2030 || Interchange - 2977189 || DIFFERENTIAL GP

$444.70

19 Jan 2019

CATERPILLAR AFTERMARKET: CATERPILLAR AFT

Caterpillar Gear-Bevel 39T 4V5393 New

01 Dec 2018
5300 Hundredths Pounds
COSTEX: COSTEX

GEAR-BEVEL
Drive Train Parts

Show more prices Caterpillar parts

Number on catalog scheme: 27

Caterpillar 4V5393 Parts scheme GEAR-BEVEL

For full view, you need register

Compatible equipment models: 4V5393:

LANDFILL COMPACTOR 816B

SOIL COMPACTOR 815B

WHEEL LOADER 966D Caterpillar

Information:

Conditions Which Generate This Code:
Illustration 1 g00721817
System Schematic For kW Level OutputThe kW level output will be activated whenever the total power output of the generator exceed the setpoint P139. The kW level output is the connector contact 34 of the GSC+. This setpoint can be programmed from 0 to 110 percent of the rated power on the nameplate (setpoint P030). This setpoint can be programmed with a time delay from 0 to 120 seconds (setpoint P140). See System Operation, "Engine/Generator Programming OP5-0". Also, see System Operation, "Service Mode". Once the output is activated, the kW level output will be deactivated when the total power output of the generator drops below a programmed setpoint (setpoint P141). This setpoint is different from the activation setpoint. This setpoint can be programmed from 0 to 110 percent of the power rating on the nameplate of the generator. This setpoint can be programmed with a time delay from 0 to 120 seconds.When kW relay is disconnected from the GSC+, the voltage on the kW level output is approximately 5.0 DCV. When kW relay is connected to the GSC+, the voltage on the kW level output is approximately 0 volts. The kW level output is capable of drawing (sinking) approximately 100 mA. Documenting and troubleshooting any connections to this output is the responsibility of the customers and the dealers. The possible cause of a CID 0859 FMI 3 is a short to the +battery circuit of the kW level output.The GSC+ treats a CID 859 FMI 03 as an alarm fault.Troubleshooting of this failure is straight forward. The FMI 03 defines the problem as a short to "B+". Use the following information in order to find the exact cause of the diagnostic code.
FMI information
system schematic of the kW level output
customer's documentation
dealer's documentationTest Step 1. CHECK THE GENERATOR SET CONTROL
Verify that the CID 0859 FMI 03 diagnostic code is active.
Disconnect the wire from contact 34 of the GSC+.
Measure the voltage between contact 34 of the GSC+ and B-.Expected Result:The voltage is approximately 5 1.0 DCV.Results:
OK - The voltage is approximately 5 1.0 DCV. The voltage is correct. Proceed to test step 2.
NOT OK - The voltage is NOT approximately 5 1.0 DCV. The voltage is NOT correct. The GSC+ has failed.Repair: It is unlikely that