6K4554 GEAR (17 TEETH) Caterpillar parts
815, 966C
Rating:
Alternative (cross code) number:
CA6K4554
6K-4554
6K4554
CA6K4554
6K-4554
6K4554
Weight: 0.01 pounds 0 kg.
SOIL COMPACTOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$51.11
26 Apr 2022
US: Florida-Parts-Z
9K1193 - Gear (17 Teeth) 2219099 4K4276 6K4554 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$54.46
02 Mar 2022
US: Florida-Parts-Z
4K4276 - Gear (17 Teeth) 6K4554 9K1193 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Number on catalog scheme:
None
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1) 1
B 128-8827 Pin(1) 1
1U-7523 Pin Pilot(1) 1
C 1U-6675 Spring Compressor(1) 6
D 128-8822 Fuel System and Governor Tool Gp 1
(1) This tool is part of the 128-8822 Governor Tool Group.
Illustration 1 g00661331Note: For information on the inspection procedure for control lever (3), refer to Special Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Loosen setscrews (4) on each bracket.
Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the bolts.
Tighten bracket (A) and (D) to a torque of 12 3 N m (106 27 lb in).
Tighten brackets (B) and (C) to a torque of 12 3 N m (106 27 lb in).
Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of 3.5 0.2 N m (31 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates freely.
The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever (3).
Illustration 2 g00750163
Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control linkage (2). Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector - Install".
Install Tooling (C) on the unit injectors and compress the springs. Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
Use Tooling (B) to install clevis pin (6) and the clip.
Use Tooling (D) to set the unit injector synchronization. Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Remove Tooling (C) from the unit injectors.
Illustration 5 g00655975
Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
Install clip (4). End By:
Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1) 1
B 128-8827 Pin(1) 1
1U-7523 Pin Pilot(1) 1
C 1U-6675 Spring Compressor(1) 6
D 128-8822 Fuel System and Governor Tool Gp 1
(1) This tool is part of the 128-8822 Governor Tool Group.
Illustration 1 g00661331Note: For information on the inspection procedure for control lever (3), refer to Special Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Loosen setscrews (4) on each bracket.
Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the bolts.
Tighten bracket (A) and (D) to a torque of 12 3 N m (106 27 lb in).
Tighten brackets (B) and (C) to a torque of 12 3 N m (106 27 lb in).
Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of 3.5 0.2 N m (31 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates freely.
The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever (3).
Illustration 2 g00750163
Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control linkage (2). Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector - Install".
Install Tooling (C) on the unit injectors and compress the springs. Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
Use Tooling (B) to install clevis pin (6) and the clip.
Use Tooling (D) to set the unit injector synchronization. Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Remove Tooling (C) from the unit injectors.
Illustration 5 g00655975
Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
Install clip (4). End By:
Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
518, 613, 613B, 815, 950, 966C
613, 950, 966C
814, 816, 966C
814, 816, 950, 966C
815, 966C
814, 950, 966C
814, 950, 966C
815, 966C
515, 525, 966C
528, 814, 815, 966C
815, 966C
980, 980B