7G8135 GEAR Caterpillar parts
936, 936F, 950B, 950B/950E, G936
Rating:
Alternative (cross code) number:
CA7G8135
7G-8135
7G8135
CA7G8135
7G-8135
7G8135
Weight: 34 pounds 15 kg.
WHEEL LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2023-02-01
2020-01-14
Information:
5. Lock or block the saw blade to prevent rotation.6. Engage saw circuit and set saw pump pressure compensator (2) to 24 800 kPa (3600 psi).7. Turn the begin of stroke adjusting screw on the saw motor out until the gauge on the "M" motor port reads 0 kPa (0 psi). Then slowly turn the adjusting screw in until the pressure gauge on the "M" port starts to rise. The pressure will continue to rise, even with no further adjustment of the screw.Make the setting when a rise in pressure is in the 3450 kPa (500 psi) to 5510 kPa (800 psi) range. Lock the jam nut on the adjusting screw.8. Adjust auxiliary pump pressure compensator (2) to 29 280 kPa (4250 psi).9. Adjust saw control valve main relief valve (3) to 28 940 kPa (4200 psi).10. Readjust auxiliary pump pressure compensator (2) back to 29 280 kPa (4250 psi).11. Remove the saw blade locking or blocking device to permit free saw blade rotation. Engage the saw circuit and bring the engine to high idle speed. Check saw blade RPM using a suitable tachometer. Set the saw speed by adjusting the motor minimum displacement stop. Consult the saw manufacturer to determine the correct saw speed specifications. Adjust the minimum displacement screw in for slower saw speeds and out for faster speeds.
Do not attempt to adjust minimum displacement screw while the saw blade is turning. Shut down saw to adjust between readings.
12. To confirm the correct motor pressure compensator settings, set engine to hi idle, have an assistant engage saw circuit and monitor the saw pump pressure reading with a gauge in the saw feed line. The gauge should read 27 560 kPa (4000 psi) (pump compensator setting) for approximately 10 seconds when the saw circuit is engaged. The pressure will then drop to 24 120 kPa (3500 psi) to 25 500 kPa (3700 psi) (motor begin of stroke point) for about 12-15 seconds. As the saw blade approaches full speed the pressure will drop lower.13. If the first pressure reading is not 27 560 kPa (4000 psi), adjust auxiliary pump compensator (2) as described in the procedure above.14. If the second pressure reading is between 24 120 kPa (3500 psi) and 25 500 kPa (3700 psi) no further adjustment is necessary.15. If the second pressure reading is below 24 120 kPa (3500 psi), turn the begin of stroke adjusting screw out slightly and redo procedure.16. If the second pressure reading is above 25 500 kPa (3700 psi), turn the begin of stroke adjusting screw in slightly and redo procedure.16. Check saw speed up time from engaging the saw circuit until saw feed pressure drops below 24 120 kPa (3500 psi) and compare to saw manufacturers recommendations. The approximate speed up time should be between 28 and 36 seconds.Adjustment Of Stroke Limiters (Side Tilt Operation)
Five valve bank
(1) Side tilt valve. (2) Stroke limiter. (3) Stroke limiter.Stroke limiters (2) and (3) permit adjustment of the speed for the side tilt
Do not attempt to adjust minimum displacement screw while the saw blade is turning. Shut down saw to adjust between readings.
12. To confirm the correct motor pressure compensator settings, set engine to hi idle, have an assistant engage saw circuit and monitor the saw pump pressure reading with a gauge in the saw feed line. The gauge should read 27 560 kPa (4000 psi) (pump compensator setting) for approximately 10 seconds when the saw circuit is engaged. The pressure will then drop to 24 120 kPa (3500 psi) to 25 500 kPa (3700 psi) (motor begin of stroke point) for about 12-15 seconds. As the saw blade approaches full speed the pressure will drop lower.13. If the first pressure reading is not 27 560 kPa (4000 psi), adjust auxiliary pump compensator (2) as described in the procedure above.14. If the second pressure reading is between 24 120 kPa (3500 psi) and 25 500 kPa (3700 psi) no further adjustment is necessary.15. If the second pressure reading is below 24 120 kPa (3500 psi), turn the begin of stroke adjusting screw out slightly and redo procedure.16. If the second pressure reading is above 25 500 kPa (3700 psi), turn the begin of stroke adjusting screw in slightly and redo procedure.16. Check saw speed up time from engaging the saw circuit until saw feed pressure drops below 24 120 kPa (3500 psi) and compare to saw manufacturers recommendations. The approximate speed up time should be between 28 and 36 seconds.Adjustment Of Stroke Limiters (Side Tilt Operation)
Five valve bank
(1) Side tilt valve. (2) Stroke limiter. (3) Stroke limiter.Stroke limiters (2) and (3) permit adjustment of the speed for the side tilt
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
4V7545
GEAR-RING
508, 518, 725, 725C, 730, 936, D250B, D250E, D250E II, D300B, D300D, G936
508, 518, 725, 725C, 730, 936, D250B, D250E, D250E II, D300B, D300D, G936
6W2900
GEAR (40 TEETH)
518, 936, D250B, D300B, D300D, G936
518, 936, D250B, D300B, D300D, G936
3T9012
GEAR (86 TEETH)
936, 936F, 966C, G936
936, 936F, 966C, G936
3T4409
GEAR (57 TEETH)
936, 950F
936, 950F
3T4224
GEAR (54 TEETH)
330 L, 936, 936F, 950B, 950B/950E, 966C, 966R, G936
330 L, 936, 936F, 950B, 950B/950E, 966C, 966R, G936
9W4950
GEAR-SUN
936, 936F, 950B, 950B/950E, 950F, 950F II, 966R, G936, R1300G
936, 936F, 950B, 950B/950E, 950F, 950F II, 966R, G936, R1300G
3T4223
GEAR-TRANSFER
936, 936F, 950B, 950B/950E, 966C, G936
936, 936F, 950B, 950B/950E, 966C, G936
1T1674
GEAR AS-DRIVE
936, 936F, 966C, G936
936, 936F, 966C, G936
1T1631
GEAR-PUMP DRIVE
950B, 950B/950E, 950F
950B, 950B/950E, 950F
3T3347
GEAR-PUMP DRIVE
950B, 950B/950E, 950F
950B, 950B/950E, 950F
7G4312
GEAR (61 teeth)
950B, 950B/950E, 966C
950B, 950B/950E, 966C
8V3135
GEAR (16 TEETH)
950B, 950B/950E, 966C, D25C, D30C, D350C, D35C, D35HP, D400
950B, 950B/950E, 966C, D25C, D30C, D350C, D35C, D35HP, D400
7G8134
GEAR
936, 936F, 950B, 950B/950E, G936
936, 936F, 950B, 950B/950E, G936
3T4410
GEAR-TRANSFER
936, 950F, G936
936, 950F, G936
9G1232
GEAR-SUN
936, 950B, 950B/950E, 966C, G936
936, 950B, 950B/950E, 966C, G936
7G5589
GEAR-RING
936, 936F, 950B, 950B/950E, 950F, 950F II, 966C, G936, R1300, R1300G
936, 936F, 950B, 950B/950E, 950F, 950F II, 966C, G936, R1300, R1300G
1W1128
GEAR AS-GOVERNOR DRIVE
641B, 777, D10
641B, 777, D10
4V7545
GEAR-RING
508, 518, 725, 725C, 730, 936, D250B, D250E, D250E II, D300B, D300D, G936
508, 518, 725, 725C, 730, 936, D250B, D250E, D250E II, D300B, D300D, G936
4V0093
GEAR
508, 518, 936, D250B, D300B, G936
508, 518, 936, D250B, D300B, G936
8V1537
GEAR
518, 936, D250B, D300B, G936
518, 936, D250B, D300B, G936
8V0618
GEAR
D250B, D300B, G936
D250B, D300B, G936
8V2957
GEAR (SIDE)
936, D300B, G936
936, D300B, G936
8V2797
GEAR (16 TEETH)
936, D250B, D300B, G936
936, D250B, D300B, G936