9P3320 GEAR-RING Caterpillar parts
589, D8L, D9N, D9R, D9T
Rating:
Alternative (cross code) number:
CA9P3320
9P-3320
9P3320
CA9P3320
9P-3320
9P3320
Weight: 225 pounds 102 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$2,879.99
04 Apr 2022
US: Florida-Parts-Z
9P3320 - Gear Ring fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
This part in 2 request:
Show.
This information for suppliers only!
2022-06-22
2019-02-08
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-6357(1)
or
8T-3022(2) Connecting Rod Guide 1
B 235-0612 Lift Bracket 1
C 136-1452 Retaining Ring Pliers As 1
D 318-3117 Ring Expander Gp 1
E 229-3611 Cover 1
F - Board
51 mm by 152 mm by 1.8 m (2 inch by 6 inch by 6.0 ft) 2
G 1U-8692 Piston Pin Guide 1
H 4C-5719 Piston Ring Compressor 1
J 8T-5096
or
1U-8869 Dial Indicator 1
K - Bel-Ray Molylube: PN. 67700 -
(1) Use with V-engines
(2) Use with in-line enginesNote: Use 8T-0447 Dial Calipers to measure the dimensions in the following procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information. Refer to page 7 for torque values.
Illustration 1 g03374611Note: Ensure that there is no damage to the shank of connecting rod bolt (3) prior to the installation of heat shrink tube (10).Note: Ensure that the shanks of connecting rod bolts (3) are free of debris and oil prior to installation.
If a new heat shrink tube needs to be installed, follow Step 1.a through Step 1.d.
Clean the shank of connecting rod bolt (3) free of debris and oil.
Slide the new heat shrink tube (10) onto connecting rod bolt (3). Install the new heat shrink tube (10) to Dimension (Y). Dimension (Y) is 1.50 mm (0.059 inch).
Use a suitable heat gun or use a suitable oven to shrink the heat shrink tube (10) onto connecting rod bolt (3). If a suitable oven is used, heat the connecting rod bolt (3) and heat shrink tube (10) at a temperature of 135° 14° C (275° 57°F) for 10 minutes.
After installing the new heat shrink tube (10) onto connecting rod bolt (3), allow connecting rod bolt (3) to cool. Ensure that heat shrink tube (10) does not have any bumps or wrinkles. Ensure that the heat shrink tube (10) does not move under light finger pressure.
Illustration 2 g03376355Note: Ensure that piston (4) is clean and meets reuse guidelines.
Use an inside micrometer to measure the inside diameter of the bore of the piston pin bearing. Refer to Specifications, "Connecting Rod".
Use an inside micrometer to measure the inside diameter of the connecting rod bearing. Make the measurement through the center line of the connecting rod. Refer to Specifications, "Connecting Rod".
Before the piston rings are installed on the piston, check the end gap on each piston ring. Refer to Specifications, "Piston and Rings".
Do not install the piston rings without the use of the piston ring expander. Piston ring breakage and piston damage may result if the piston ring expander is not used.
Use Tooling (D) to install the piston rings on piston (4).
The piston ring gaps should be separated by 120 degrees. Install the piston rings in the following manner:
Install the piston ring expander on the piston. The ends of
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-6357(1)
or
8T-3022(2) Connecting Rod Guide 1
B 235-0612 Lift Bracket 1
C 136-1452 Retaining Ring Pliers As 1
D 318-3117 Ring Expander Gp 1
E 229-3611 Cover 1
F - Board
51 mm by 152 mm by 1.8 m (2 inch by 6 inch by 6.0 ft) 2
G 1U-8692 Piston Pin Guide 1
H 4C-5719 Piston Ring Compressor 1
J 8T-5096
or
1U-8869 Dial Indicator 1
K - Bel-Ray Molylube: PN. 67700 -
(1) Use with V-engines
(2) Use with in-line enginesNote: Use 8T-0447 Dial Calipers to measure the dimensions in the following procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information. Refer to page 7 for torque values.
Illustration 1 g03374611Note: Ensure that there is no damage to the shank of connecting rod bolt (3) prior to the installation of heat shrink tube (10).Note: Ensure that the shanks of connecting rod bolts (3) are free of debris and oil prior to installation.
If a new heat shrink tube needs to be installed, follow Step 1.a through Step 1.d.
Clean the shank of connecting rod bolt (3) free of debris and oil.
Slide the new heat shrink tube (10) onto connecting rod bolt (3). Install the new heat shrink tube (10) to Dimension (Y). Dimension (Y) is 1.50 mm (0.059 inch).
Use a suitable heat gun or use a suitable oven to shrink the heat shrink tube (10) onto connecting rod bolt (3). If a suitable oven is used, heat the connecting rod bolt (3) and heat shrink tube (10) at a temperature of 135° 14° C (275° 57°F) for 10 minutes.
After installing the new heat shrink tube (10) onto connecting rod bolt (3), allow connecting rod bolt (3) to cool. Ensure that heat shrink tube (10) does not have any bumps or wrinkles. Ensure that the heat shrink tube (10) does not move under light finger pressure.
Illustration 2 g03376355Note: Ensure that piston (4) is clean and meets reuse guidelines.
Use an inside micrometer to measure the inside diameter of the bore of the piston pin bearing. Refer to Specifications, "Connecting Rod".
Use an inside micrometer to measure the inside diameter of the connecting rod bearing. Make the measurement through the center line of the connecting rod. Refer to Specifications, "Connecting Rod".
Before the piston rings are installed on the piston, check the end gap on each piston ring. Refer to Specifications, "Piston and Rings".
Do not install the piston rings without the use of the piston ring expander. Piston ring breakage and piston damage may result if the piston ring expander is not used.
Use Tooling (D) to install the piston rings on piston (4).
The piston ring gaps should be separated by 120 degrees. Install the piston rings in the following manner:
Install the piston ring expander on the piston. The ends of
Cat SIS web machinery list:
Parts gear Caterpillar catalog:
6I9059
GEAR AS-PUMP
589, D10N, D9N, D9R
589, D10N, D9N, D9R
6I9057
GEAR AS-OIL PUMP
589, D10N, D9N, D9R
589, D10N, D9N, D9R
3P0747
GEAR-OIL PUMP
589, 768C, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776, 776C, 776D, 777, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 789D, 793, 793B, 834G, 834H, 836G, 836H, 988G, 988H, AD40, A...
589, 768C, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776, 776C, 776D, 777, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 789D, 793, 793B, 834G, 834H, 836G, 836H, 988G, 988H, AD40, A...
7G2244
GEAR AS-PUMP
589, D10N, D8L, D9L
589, D10N, D8L, D9L
9M2074
GEAR-RING
589, 834, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
589, 834, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
7G5622
GEAR-PLANETARY
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
8E7838
GEAR-SUN
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9R
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9R
7G3454
GEAR
14G, 14H, 14H NA, 16G, 16H, 16H NA, 578, 583R, 589, 613C, 613C II, 613G
14G, 14H, 14H NA, 16G, 16H, 16H NA, 578, 583R, 589, 613C, 613C II, 613G
3T1447
GEAR
572R, 572R II, 578, 583R, 587R, 587T, D6H, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D8N, D9R, PL87
572R, 572R II, 578, 583R, 587R, 587T, D6H, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D8N, D9R, PL87
7G2500
GEAR-PLANETARY
578, 621E, 621F, 621G, 621H, 621K, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, D10N, D10R, D6H, D6H II, D6H XL, D6H XR, D7G, D7H, D7R, D8L, D8N, D8R, D9...
578, 621E, 621F, 621G, 621H, 621K, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, D10N, D10R, D6H, D6H II, D6H XL, D6H XR, D7G, D7H, D7R, D8L, D8N, D8R, D9...
3P2810
GEAR (ring-40 teeth)
824C, 826C, 834B, 980C, 980F, 980F II, 980G, 980G II, 983B, 988B, D400, D44B, D8L, D9L
824C, 826C, 834B, 980C, 980F, 980F II, 980G, 980G II, 983B, 988B, D400, D44B, D8L, D9L
9G1499
GEAR-OIL PUMP
AD30, D11N, D11R, D250E II, D300E II, D6H, D8N, D9L, D9N, D9R
AD30, D11N, D11R, D250E II, D300E II, D6H, D8N, D9L, D9N, D9R
9P3471
GEAR-SUN
589, D8L, D9N, D9R, D9T
589, D8L, D9N, D9R, D9T
9P3366
GEAR-PLANETARY
589, D8L, D9N, D9R, D9T
589, D8L, D9N, D9R, D9T
9P3429
GEAR-PLANETARY
589, D8L, D9N, D9R, D9T
589, D8L, D9N, D9R, D9T
2W7610
GEAR
24H, 589, 834B, 836, 988B, AD40, AD45, AE40, AE40 II, D10N, D10R, D8L, D9L, D9N, D9R
24H, 589, 834B, 836, 988B, AD40, AD45, AE40, AE40 II, D10N, D10R, D8L, D9L, D9N, D9R
2W7609
GEAR
24H, 589, 834B, 836, 988B, PM-565, PM-565B
24H, 589, 834B, 836, 988B, PM-565, PM-565B
2W7614
GEAR-CRANKSHAFT
589, D10N, D10R, D8L, D9L, D9N, D9R
589, D10N, D10R, D8L, D9L, D9N, D9R
9G1918
GEAR-SUN
589, 834B, AD30, D10N, D350E, D350E II, D400, D400E, D44B, D550B, D8L, D9L, D9N, D9R, D9T, R2900, R2900G, R3000H
589, 834B, AD30, D10N, D350E, D350E II, D400, D400E, D44B, D550B, D8L, D9L, D9N, D9R, D9T, R2900, R2900G, R3000H
8E7860
GEAR-BEVEL
589, D10N, D8L, D9N, D9R
589, D10N, D8L, D9N, D9R
9W5168
GEAR-BEVEL
589, D10N, D8L, D9N
589, D10N, D8L, D9N
8P6241
GEAR-BEVEL
589, D8L, D9L, D9N
589, D8L, D9L, D9N
9P3454
GEAR-SUN
589, D8L, D9N, D9R
589, D8L, D9N, D9R