9P3710 GEAR-SUN Caterpillar parts
D6H, D6H XL, D6H XR, D7H
Rating:
Alternative (cross code) number:
CA9P3710
9P-3710
9P3710
CA9P3710
9P-3710
9P3710
Weight: 17 pounds 7 kg.
TRACK-TYPE TRACTOR,
Information:
Removal Procedure (Transmission Output Speed Sensor)
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Illustration 1 g01210404
Disconnect harness assembly (1). Remove the bolt and retainer (2) and speed sensor (3) .
Illustration 2 g01210427
Remove O-ring seal (4) .
Repeat for the remaining transmission output speed sensor.Removal Procedure (Engine Output Speed Sensor)
Illustration 3 g01210411
Disconnect harness assembly (1). Loosen nut (3). Remove speed sensor (2) and seal (4) .Removal Procedure (Torque Converter Output Speed Sensor)
Illustration 4 g01210412
Disconnect harness assembly (1). Loosen nut (2). Remove speed sensor (3) and seal (4) .Installation Procedure (Transmission Output Speed Sensor)
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 5 g01210427
Install O-ring seal (4) .
Illustration 6 g01210404
Install speed sensor (3). Install the bolt and retainer (2). Connect harness assembly (1) .
Repeat for the remaining speed sensor.Installation Procedure (Engine Output Speed Sensor)
Illustration 7 g01210411
Install seal (4). Install speed sensor (2) until speed sensor (2) lightly contacts a gear tooth. Loosen speed sensor (3) for one half of a turn. Tighten nut (3) to a torque of 25 5 N m (18 4 lb ft). Connect harness assembly (1) .Installation Procedure (Torque Converter Output Speed Sensor)
Illustration 8 g01210412
Install seal (4). Install speed sensor (3) until speed sensor (3) lightly contacts a gear tooth. Loosen speed sensor (3) for one half of a turn. Tighten nut (2) to a torque of 25 5 N m (18 4 lb ft). Connect harness assembly (1) .
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Illustration 1 g01210404
Disconnect harness assembly (1). Remove the bolt and retainer (2) and speed sensor (3) .
Illustration 2 g01210427
Remove O-ring seal (4) .
Repeat for the remaining transmission output speed sensor.Removal Procedure (Engine Output Speed Sensor)
Illustration 3 g01210411
Disconnect harness assembly (1). Loosen nut (3). Remove speed sensor (2) and seal (4) .Removal Procedure (Torque Converter Output Speed Sensor)
Illustration 4 g01210412
Disconnect harness assembly (1). Loosen nut (2). Remove speed sensor (3) and seal (4) .Installation Procedure (Transmission Output Speed Sensor)
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 5 g01210427
Install O-ring seal (4) .
Illustration 6 g01210404
Install speed sensor (3). Install the bolt and retainer (2). Connect harness assembly (1) .
Repeat for the remaining speed sensor.Installation Procedure (Engine Output Speed Sensor)
Illustration 7 g01210411
Install seal (4). Install speed sensor (2) until speed sensor (2) lightly contacts a gear tooth. Loosen speed sensor (3) for one half of a turn. Tighten nut (3) to a torque of 25 5 N m (18 4 lb ft). Connect harness assembly (1) .Installation Procedure (Torque Converter Output Speed Sensor)
Illustration 8 g01210412
Install seal (4). Install speed sensor (3) until speed sensor (3) lightly contacts a gear tooth. Loosen speed sensor (3) for one half of a turn. Tighten nut (2) to a torque of 25 5 N m (18 4 lb ft). Connect harness assembly (1) .
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
3T8757
GEAR
527, 561M, 561N, 572R, 572R II, 613G, D10T2, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6H, D6H XL, D6H XR, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D7H, D7R, D7R II, D8N, D8R
527, 561M, 561N, 572R, 572R II, 613G, D10T2, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6H, D6H XL, D6H XR, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D7H, D7R, D7R II, D8N, D8R
9G8637
GEAR-SUN
D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL
D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL
6Y0926
GEAR-PLANETARY
583T, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83
583T, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83
3T4715
GEAR-SUN
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D7H, D7R, D7R II, D8N, D8R, D8R II
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D7H, D7R, D7R II, D8N, D8R, D8R II
6Y0984
GEAR-RING
583T, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83
583T, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83
9G0291
GEAR-RING
814B, 815B, 966D, 966F, 966F II, 970F, 980C, D6H, D6H XL, D6H XR, D7H
814B, 815B, 966D, 966F, 966F II, 970F, 980C, D6H, D6H XL, D6H XR, D7H
9P8521
GEAR-RING
966D, 966F, 966F II, D6H, D6H XL, D6H XR, D6R, D6R II
966D, 966F, 966F II, D6H, D6H XL, D6H XR, D6R, D6R II
9M8281
GEAR AS-PUMP
966C, D5, D5B, D6H, D6H XL, D6H XR, D7H, D7R, D8R
966C, D5, D5B, D6H, D6H XL, D6H XR, D7H, D7R, D8R
2442310
GEAR-PLANETARY
583T, D5R LGP, D6H XL, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR, D8R, D8R II, D8T, PL83
583T, D5R LGP, D6H XL, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR, D8R, D8R II, D8T, PL83
7T6578
GEAR-PLANETARY
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
7T6580
GEAR-RING
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
9G9543
GEAR
769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776, 776C, 776D, 777, 777D, 785, AD40, AD45, AE40, AE40 II, D10R, D6H, D7H
769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776, 776C, 776D, 777, 777D, 785, AD40, AD45, AE40, AE40 II, D10R, D6H, D7H
9W3713
GEAR
D6H, D6H XL, D6H XR
D6H, D6H XL, D6H XR
9W3714
GEAR
561N, D5M, D5N, D6H, D6H XL, D6H XR, D6M, D6N, D9T
561N, D5M, D5N, D6H, D6H XL, D6H XR, D6M, D6N, D9T
9W9018
GEAR
D6H, D6H XL, D6H XR, D7H
D6H, D6H XL, D6H XR, D7H
9M8281
GEAR AS-PUMP
966C, D5, D5B, D6H, D6H XL, D6H XR, D7H, D7R, D8R
966C, D5, D5B, D6H, D6H XL, D6H XR, D7H, D7R, D8R
3T8927
GEAR AS-PUMP
D6H, D6H XL, D6H XR, D7H, D7R, D8R
D6H, D6H XL, D6H XR, D7H, D7R, D8R
6I8505
GEAR-PLANETARY
D6H, D6H XL, D6H XR, D6R, D6R II
D6H, D6H XL, D6H XR, D6R, D6R II
7T8844
GEAR AS-2ND
D6H, D7H
D6H, D7H
7T8848
GEAR AS-4TH
D6H, D7H
D6H, D7H
7T8852
GEAR AS-6TH
D6H, D7H
D6H, D7H
7T8869
GEAR AS-REVERSE
D6H, D7H
D6H, D7H
9W5924
GEAR AS-FORWARD
D6H, D7H
D6H, D7H
6T5974
GEAR
D6H, D6H XL, D6H XR
D6H, D6H XL, D6H XR