9S6874 GEAR AND PINION Caterpillar parts
571G, 572G, D7F, D7G, D7G2
Rating:
Alternative (cross code) number:
CA9S6874
9S-6874
9S6874
CA9S6874
9S-6874
9S6874
Weight: 142 pounds 64 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Compatible equipment models: 9S6874:
Information:
Table 1
Event Code
Description Conditions which Activate the Code System Response
E225(3) Engine Overcrank The engine did not start within the programmed parameters for engine starting. The code is logged.
The alarm output is activated. Probable Causes
Fuel supply
Faulty starting motor circuit
Faulty speed/timing circuit
Active diagnostic codes
Incorrect base timing
Fuel quality
Programmable parametersRecommended Actions
Fuel Supply
Use Cat ET to check that the engine's fuel parameters are correct for the fuel that is being used. If necessary, perform fuel analysis in order to confirm the fuel quality.Verify that the fuel pressure is correct. When possible, interview the operator in order to determine if fuel quality is in question. Try to determine if the source of the fuel has been changed.Ensure that fuel is supplied at a sufficient pressure that is stable. Check that the size of the fuel line is sufficient. Inspect the fuel system for leaks.The following conditions can affect engine starting:
Low fuel pressure
High fuel pressure
Poor fuel qualityInspect the following fuel system components:
Fuel filter
Gas pressure regulator
Gas shutoff valve
Fuel metering valveCheck the fuel metering valve's status indicator that is located on the top of the valve. If the status indicator is flashing orange or flashing red there is an internal error for the valve. Before performing maintenance on the valve, observe the status indicator. Refer to Operation and Maintenance Manual, SEBU7630, "WOODWARD RAPTOR GAS REGULATION AND METERING VALVE/ACTUATOR SYSTEM" for detailed information about flash codes and for information that is related to troubleshooting the fuel metering valve.Verify that the system's components are operating correctly.Repair suspect components. Replace the fuel filter, if necessary.Faulty Starting Motor Circuit
Check the air supply if the engine is equipped with an air starting motor. For engines that are equipped with electric starting motors, check the battery connections and the requirements for the cable sizes.Attempt to start the engine while you observe the "Starter Motor Relay" parameter on Cat ET.If the status of the relay for the starting motor indicates that the engine should crank but no cranking occurs, troubleshoot the starting circuit. Refer to Troubleshooting, "Starting - Test".Faulty Speed/Timing Circuit
Attempt to start the engine. Use Cat ET to observe the "Engine Speed" parameter for an indication of engine rpm. The master Electronic Control Module (ECM) must detect a minimum of 50 rpm before the gas and the ignition are supplied to the engine.If no engine speed is displayed on Cat ET or if the engine speed is unstable, troubleshoot the speed/timing sensor. Refer to Troubleshooting, "Speed/Timing - Test" in order to troubleshoot this problem.Active Diagnostic Codes
Check for active diagnostic codes that relate to the ignition system. If there are any active diagnostic codes that are related to the ignition system, troubleshoot the diagnostic code.Incorrect Base Timing
Verify that the base timing is correct. Refer to Systems Operation/Testing and Adjusting, "Ignition Timing - Adjust".Fuel Quality
Compare the Low Heat Value (LHV) of the gas supply to the "Fuel Quality" parameter that is programmed by the customer into the master ECM. The master ECM uses the setting for start-up and for air/fuel ratio control at low loads.If
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
1144680
GEAR AS-OIL PUMP
D7G, D7G2
D7G, D7G2
5M1143
GEAR ASSEM. (29 TEETH)
D7F, D7G
D7F, D7G
5M1133
GEAR (46 & 41 TEETH)
D7F, D7G
D7F, D7G
8H7810
GEAR (26T)
D7F, D7G, D8H, D8K
D7F, D7G, D8H, D8K
5M1139
GEAR ASSEM. (45T)
D7F, D7G
D7F, D7G
5M1147
GEAR ASSEM. (47T)
D7F, D7G
D7F, D7G
5M1145
GEAR ASSEM. (47T)
D7F, D7G
D7F, D7G
2P4714
GEAR (52 TEETH)
D9G, D9H
D9G, D9H
6N4845
GEAR (59teeth)
594H, D9H
594H, D9H
2V6716
GEAR (34 teeth)
955K, 955L
955K, 955L
2K1494
GEAR (21T.)
572G, 594, 594H
572G, 594, 594H
9F3812
GEAR
572G, 594, 594H
572G, 594, 594H
2K1714
GEAR ASSEM. (43&26T.)
572G, 594, 594H
572G, 594, 594H
2K1716
GEAR ASSEM. (35&26T.)
572G, 594, 594H
572G, 594, 594H
2K1720
GEAR ASSEM. (31&26T.)
572G, 594, 594H
572G, 594, 594H
2P3424
GEAR (47 teeth)
571G, 572G, D7G
571G, 572G, D7G