9W5773 GEAR Caterpillar parts
910
Rating:
Alternative (cross code) number:
CA9W5773
9W-5773
9W5773
CA9W5773
9W-5773
9W5773
Weight: 12 pounds 5 kg.
COMPACT WHEEL LOADER,
Compatible equipment models: 9W5773:
Information:
The following line relief valves are located on top of the main control valve: boom cylinder rod end, bucket cylinder head end and stick cylinder head end. The line relief valve for the bucket cylinder rod end is located under the main control valves.
Illustration 4 g00369374
(10) Line relief valve (boom cylinder head end) (11) Boom drift reduction valveThe line relief valve for the boom cylinder head end (10) is located at boom drift reduction valve (11).
Illustration 5 g00369375
(12) Line relief valve (stick cylinder rod end) (13) Stick drift reduction valveThe line relief valve for the stick cylinder rod end (12) is located at stick drift reduction valve (13).
Illustration 6 g00343372
(14) Locknut (15) Adjustment screw
Illustration 7 g00343412
(16) Locknut (17) CapNote: Return main relief valve pressure to the specification after testing and adjusting any line relief valve. Refer to Testing And Adjusting, "Pressure Specifications" for the main relief valve pressure setting.Note: In order to cancel Service Mode, depress the following three buttons on the operator monitor panel at the same time: button for fine control (4), button for user mode (5) and travel alarm cancel switch (6). Hold all three buttons down for at least three seconds. If the engine switch key is placed in the OFF position for at least 75 15 seconds, Service Mode will be cancelled.Adjust
Stick Cylinder
To adjust the line relief valve pressure setting of the stick cylinder rod end, move the stick control lever until the stick is at the full STICK OUT position (full retraction of stick cylinder).
Check the pressure in the stick cylinder rod end on the pressure gauge at pressure tap (3) .
Return the stick control lever to the NEUTRAL position.
Loosen locknut (14) or (16) on the stick line relief valve. Turn adjustment screw (15) or turn cap (17) until the pressure gauge reading at pressure tap (3) is 36800 1470 kPa (5350 215 psi).
To adjust the line relief valve pressure setting of the stick cylinder head end, move the stick control lever until the stick is at the full STICK IN position (full extension of stick cylinder).
Check the pressure in the stick cylinder head end on the pressure gauge at pressure tap (3) .
Return the stick control lever to the NEUTRAL position.
Loosen locknut (14) or (16) on the stick line relief valve. Turn adjustment screw (15) or turn cap (17) until the pressure gauge reading at pressure tap (3) is 36800 1470 kPa (5350 215 psi).
After completion of line relief valve adjustment, tighten locknut (14) or (16) .Note: Turning adjustment screw (15) or turning cap (17) clockwise increases the pressure. Turning adjustment screw (15) or turning cap (17) counterclockwise decreases the pressure.Note: Always make final pressure adjustment on pressure rise.Bucket Cylinder
To adjust the line relief valve pressure setting of the bucket cylinder head end, move
Illustration 4 g00369374
(10) Line relief valve (boom cylinder head end) (11) Boom drift reduction valveThe line relief valve for the boom cylinder head end (10) is located at boom drift reduction valve (11).
Illustration 5 g00369375
(12) Line relief valve (stick cylinder rod end) (13) Stick drift reduction valveThe line relief valve for the stick cylinder rod end (12) is located at stick drift reduction valve (13).
Illustration 6 g00343372
(14) Locknut (15) Adjustment screw
Illustration 7 g00343412
(16) Locknut (17) CapNote: Return main relief valve pressure to the specification after testing and adjusting any line relief valve. Refer to Testing And Adjusting, "Pressure Specifications" for the main relief valve pressure setting.Note: In order to cancel Service Mode, depress the following three buttons on the operator monitor panel at the same time: button for fine control (4), button for user mode (5) and travel alarm cancel switch (6). Hold all three buttons down for at least three seconds. If the engine switch key is placed in the OFF position for at least 75 15 seconds, Service Mode will be cancelled.Adjust
Stick Cylinder
To adjust the line relief valve pressure setting of the stick cylinder rod end, move the stick control lever until the stick is at the full STICK OUT position (full retraction of stick cylinder).
Check the pressure in the stick cylinder rod end on the pressure gauge at pressure tap (3) .
Return the stick control lever to the NEUTRAL position.
Loosen locknut (14) or (16) on the stick line relief valve. Turn adjustment screw (15) or turn cap (17) until the pressure gauge reading at pressure tap (3) is 36800 1470 kPa (5350 215 psi).
To adjust the line relief valve pressure setting of the stick cylinder head end, move the stick control lever until the stick is at the full STICK IN position (full extension of stick cylinder).
Check the pressure in the stick cylinder head end on the pressure gauge at pressure tap (3) .
Return the stick control lever to the NEUTRAL position.
Loosen locknut (14) or (16) on the stick line relief valve. Turn adjustment screw (15) or turn cap (17) until the pressure gauge reading at pressure tap (3) is 36800 1470 kPa (5350 215 psi).
After completion of line relief valve adjustment, tighten locknut (14) or (16) .Note: Turning adjustment screw (15) or turning cap (17) clockwise increases the pressure. Turning adjustment screw (15) or turning cap (17) counterclockwise decreases the pressure.Note: Always make final pressure adjustment on pressure rise.Bucket Cylinder
To adjust the line relief valve pressure setting of the bucket cylinder head end, move
Caterpillar parts catalog:
Parts gear Caterpillar catalog:
2N1599
GEAR
214B, 224B, 3114, 3116, 3126, 3126B, 3160, 3204, 3208, 320B, 322B LN, 325, 325B, 325B L, 446, 446B, 508, 574, 910, 918F, 924F, 931B, 933, 933C, 939, 939C, C7, CB-614, CS-531D, CS-533D, CS-551, D3C III...
214B, 224B, 3114, 3116, 3126, 3126B, 3160, 3204, 3208, 320B, 322B LN, 325, 325B, 325B L, 446, 446B, 508, 574, 910, 918F, 924F, 931B, 933, 933C, 939, 939C, C7, CB-614, CS-531D, CS-533D, CS-551, D3C III...
4M9933
GEAR CRANKSHAFT
120B, 120G, 12E, 140B, 14E, 1673, 1673B, 1673C, 225, 3304, 3306, 518, 561B, 561C, 572G, 627, 637D, 814, 910, 920, 931B, 941, 943, 950, 950B, 953, 955H, 955K, 955L, 963, 966C, 977H, 977K, 980B, D3, D33...
120B, 120G, 12E, 140B, 14E, 1673, 1673B, 1673C, 225, 3304, 3306, 518, 561B, 561C, 572G, 627, 637D, 814, 910, 920, 931B, 941, 943, 950, 950B, 953, 955H, 955K, 955L, 963, 966C, 977H, 977K, 980B, D3, D33...
5S5058
GEAR ASSEM.
1673, 1673B, 1673C, 215, 3304, 3306, 621R, 910, 931B, 941, 943, 950, 953, 966C, D330B, D333B, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G
1673, 1673B, 1673C, 215, 3304, 3306, 621R, 910, 931B, 941, 943, 950, 953, 966C, D330B, D333B, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G
1T1002
GEAR-DRIVE
910, 931, D3B, D3C II
910, 931, D3B, D3C II
9P3464
GEAR (10 Teeth)
910, 931B
910, 931B
9S6897
GEAR (54 Teeth)
910, 931B
910, 931B
9S6917
GEAR (54 Teeth)
910, 931B
910, 931B
9S6910
GEAR (54 Teeth)
910, 931B
910, 931B
6S3014
GEAR-DIFFERENTIAL BEVEL
910, IT12B
910, IT12B
2K8753
GEAR (11 TEETH)
518, 910, 930
518, 910, 930
3T4223
GEAR-TRANSFER
936, 936F, 950B, 950B/950E, 966C, G936
936, 936F, 950B, 950B/950E, 966C, G936
7G3207
GEAR-IDLER
926, IT28, IT28B
926, IT28, IT28B
7G3208
GEAR-DRIVE
926, IT28, IT28B
926, IT28, IT28B
2Y5124
GEAR
930, 930R
930, 930R
3T5534
GEAR
930R
930R
9W1255
GEAR
930R
930R
9W1051
GEAR
930R
930R
7T3334
GEAR
930R
930R
1T1674
GEAR AS-DRIVE
936, 936F, 966C, G936
936, 936F, 966C, G936
9W5775
GEAR
910
910
9W5774
GEAR
910
910