1994323 GENERAL AR-TRACTOR Caterpillar parts
613C II
Rating:
Alternative (cross code) number:
CA1994323
199-4323
1994323
CA1994323
199-4323
1994323
WHEEL TRACTOR,
Compatible equipment models: 1994323:
For full view, you need register
Information:
Removal Procedure
Start By:
Raise the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01344738
Remove tube assembly (1). Disconnect hose assembly (2). Position hose assembly (2) out of the way.
Illustration 2 g01344764
Disconnect harness assembly (6). Remove bolt (5), retainer (4), and solenoid valve (3) .
Illustration 3 g01344765
Remove O-ring seals (7) from solenoid valve (3) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 4 g01344765
Install O-ring seals (7) onto solenoid valve (3) .
Illustration 5 g01344764
Install solenoid valve (3), retainer (4), and bolt (5). Connect harness assembly (6).
Illustration 6 g01344738
Install tube assembly (1). Connect hose assembly (2) .End By: Lower the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Start By:
Raise the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01344738
Remove tube assembly (1). Disconnect hose assembly (2). Position hose assembly (2) out of the way.
Illustration 2 g01344764
Disconnect harness assembly (6). Remove bolt (5), retainer (4), and solenoid valve (3) .
Illustration 3 g01344765
Remove O-ring seals (7) from solenoid valve (3) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 4 g01344765
Install O-ring seals (7) onto solenoid valve (3) .
Illustration 5 g01344764
Install solenoid valve (3), retainer (4), and bolt (5). Connect harness assembly (6).
Illustration 6 g01344738
Install tube assembly (1). Connect hose assembly (2) .End By: Lower the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Caterpillar SIS machinery equipment:
Parts general Caterpillar catalog:
2132846
GENERAL AR-AIR TRANSPORT
613C II
613C II
2132820
GENERAL AR-TRACTOR
613C II
613C II
8I1466
GENERAL AR-TRACTOR
613C II
613C II
2T3150
GENERAL AR-TRACTOR
613C II
613C II
8Y8151
GENERAL AR
D3C III
D3C III
8Y8150
GENERAL AR
D3C III
D3C III