GENERAL AR 2804255 - Caterpillar

2804255 GENERAL AR Caterpillar parts C32

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2804255
280-4255
2804255

Buy GENERAL AR 2804255 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Rareelectrical NEW STARTER MOTOR COMPATIBLE WITH 2007 2008 DODGE MAGNUM V8 5.7L AWD MODELS M0T21071ZC 2804255

$101.85

24 May 2021

US: Rareelectrical

Rareelectrical NEW STARTER MOTOR COMPATIBLE WITH 2007 2008 DODGE MAGNUM V8 5.7L AWD MODELS M0T21071ZC 2804255
Rareelectrical 100% NEW and Made with the Highest Quality Components Available || Full One Year Warranty || Computer tested for consistent Quality and unsurpassed reliability || Starter - Voltage: 12V Rotation: Clockwise Teeth On Drive / Splines: 10 Source: Aftermarket

For full view, you need register

Compatible equipment models: 2804255:

GENERATOR SET C32 Caterpillar

Information:

This diagnostic code is recorded when the diagnostic circuit in the PL522 and 523 identifies a system voltage that is above 32 VDC.The possible causes of this fault are listed below:
A charging system component is faulty.
The harness wiring is faulty.
The PL522 or 523 is faulty. Module failure is unlikely.Note: Determine if a battery charger or a welder is being used on the machine. Disconnect the charger or the welder if one is used. Recheck for the diagnostic code.Test Step 1. CHECK THE SYSTEM VOLTAGE AT THE 70-PIN CONNECTOR OF THE PL522 or 523.
Start the engine and operate the engine at a high idle for 5 to10 minutes.
Measure the system voltage between the "Unswitched Power" and the "Ground" contacts. Pin 52 is the terminal for "Unswitched Power" and pin 65 is the terminal for "Ground". Expected Result:The voltage is 11 VDC to 32 VDC.Results:
OK - The voltage is 11 VDC to 32 VDC. The PL522 or 523 should not be logging this diagnostic code.Repair: Use the Caterpillar Electronic Technician (Cat ET ) in order to clear the diagnostic code from the PL522 or 523. If the voltage is correct and the PL522 or 523 records the diagnostic code again, replace the PL522 or 523. Before replacing the PL522 or 523, contact your Caterpillar Technical Communicator.STOP
NOT OK - The voltage is not 11 VDC to 32 VDC. Proceed to Test Step 2.Test Step 2. CHECK THE ALTERNATOR.
Run the engine at high idle for 5 to 10 minutes.
Measure the voltage output at the battery posts. Expected Result:The voltage should be below 32 VDC.Results:
OK - The voltage is below 32 VDC. The battery could be faulty. Proceed to Test Step 3.
NOT OK - The voltage is above 32 VDC. Troubleshoot the alternator. The voltage regulator could be faulty. If conditions are not resolved, proceed to Test Step 3.Test Step 3. CHECK THE BATTERY VOLTAGE.Turn the key start switch to the OFF position. Measure the battery voltage at the battery posts.Expected Result:The voltage should be below 32 VDC.Results:
OK - The voltage is below 32 VDC. Proceed to Test Step 4.
NOT OK - The voltage is above 32 VDC.Repair: Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".If conditions are not resolved, proceed to Test Step 4.Test Step 4. CHECK EVERY ECM ON THE MACHINE.Check the logged diagnostics of any other ECM that is installed on the machine. Compare each ECM that has logged the "CID 168 FMI 00" code in the same time period. The Service Meter Hours (SMH) on the logs may be different. The difference between the current SMH and the logged SMH is important.Expected Result:Other "CID 168 FMI 00" diagnostic codes can be found on other Electronic Control Modules (ECM).Results:
YES - "CID 168 FMI 00" diagnostic codes are found on other Electronic Control Modules (ECM).Repair: Clear the fault if all the following conditions occur:
A problem is not found with the charging system.
A problem is not found with the wiring.
The fault has occurred a few times.Monitor the module and the machine for