AVSPARE.COM
parts catalog

GENERATOR AR 1169744 - Caterpillar


1169744 GENERATOR AR Caterpillar parts 3412, 3412C, C18
Rating:
18
Alternative (cross code) number:
CA1169744
116-9744
1169744
Caterpillar 1169744 GENERATOR AR

Buy GENERATOR AR 1169744 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE, PETROLEUM GEN SET,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$800.72
 

12 Oct 2021
22.82[10.27] Pounds
US: Newparts
Genuine OEM Front Suspension Strut for Mercedes 1643205913
Newparts
  For full view, you need register

Compatible equipment models: 1169744:

GEN SET ENGINE  3412   3412C  
GENERATOR SET  C18  
MARINE ENGINE  3412C  
PETROLEUM GEN SET  C18   Caterpillar

Information:

Disassembly Procedure
Start By:
Remove the vibratory and steering pump. Refer to Disassembly and Assembly, "Gear Pump (Steering and Vibratory) - Remove".Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform the disassembly procedures on a clean work surface. Keep components covered and protected at all times.Note: In some cases, it may not be economical or it may not be practical to recondition a pump. This determination is made after disassembly and a close inspection of the pump components. Due to wear, reconditioning may not be possible. If the cost of reconditioning a pump exceeds the cost of a remanufactured pump, the pump should be replaced with a remanufactured pump instead of a reconditioned pump.
Illustration 1 g01025467
Remove bolts (3). Remove steering pump (2) from vibratory pump (1) .
Illustration 2 g01025469
Note: Steps 2 through 5 are for the disassembly of the steering pump.
Remove relief valve (7), gear assembly (5), and end cap (4) from housing (6). Remove the seal from the end cap.
Illustration 3 g01025473
Remove backup ring (9) and O-ring seal (8) from relief valve (7) .
Illustration 4 g01025477
Remove seal (10) and O-ring seal (11) from housing (6) .
Illustration 5 g01025480
Remove gear carrier (12) for each end of the gear assembly. Remove seal retainer (13) and seal (14) .
Illustration 6 g01025483
Note: Steps 6 through 12 are for the disassembly of the vibratory pump.
Remove bolts (15) and nuts (16) which hold the vibratory pump together. Remove mounting flange (17) from the housing.
Illustration 7 g01096268
Remove O-ring seal (19) from mounting flange (17). Remove lip seal (18) from the mounting flange, if necessary.
Illustration 8 g01025487
Remove seal (20), seal retainer (21), and seal (22) from the mounting flange.
Illustration 9 g01025488
Remove wear plate (24) from housing (23) .
Illustration 10 g01025490
Remove gear assemblies (25) from housing (23) .
Illustration 11 g01025495
Remove wear plate (26) and housing (23) from end cover (27) .
Illustration 12 g01025501
Remove seal (28) and seal retainer (29) from end cover (27). Remove the seal that was under the retainer.


Parts generator Caterpillar catalog:

1091600 GENERATOR GP
3412, 3412C, C18, PM3412
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.