GOV, FUEL INJ & TFR PUMP GP 2W8961 - Caterpillar

2W8961 GOV, FUEL INJ & TFR PUMP GP Caterpillar parts 631D, 631E, 633D, 637D, 637E, 639D, 768C, 769C, 771C

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2W8961
2W-8961
2W8961

Caterpillar 2W8961 GOV, FUEL INJ & TFR PUMP GP

Weight: 10 pounds 4 kg.

Buy GOV, FUEL INJ & TFR PUMP GP 2W8961 Caterpillar genuine, new aftermarket tractor parts with delivery
QUARRY TRUCK, WHEEL TRACTOR,

Compatible equipment models: 2W8961:

QUARRY TRUCK 771C

TRACTOR 768C

TRUCK 769C

WHEEL TRACTOR 631D 631E 633D 637D 637E 639D Caterpillar

Number on catalog scheme:

Caterpillar 2W8961 Parts scheme GOV, FUEL INJ & TFR PUMP GP

For full view, you need register

Information:

TYPE="LEVEL" DEPTH="1" @@@-->Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Turbocharged Engines
Illustration 1 g00743960
Put the heat exchanger into position and install bolt (8) onto support brackets. Note: If the brackets have been removed, apply Loctite 603 to the bolts that attach the brackets to the cylinder block.
Install two bolts (9) at the front of the heat exchanger to the support bracket.
Illustration 2 g00758463
Install water temperature regulator housing (7) onto the heat exchanger. Slide hose (2) into position and tighten the hose clamps. Slide hose (4) into position and tighten the hose clamps.
Slide hose (3) into position and tighten the hose clamps.
Slide hose (1) into position and tighten the hose clamps.
Install hose (5) and hose (6) onto the heat exchanger. Tighten the hose clamps.
Install the drain plug for the engine coolant. Install the drain plug for the sea water circuit.
Fill the cooling system. If the engine uses diesel engine antifreeze/coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses extended life coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Open the valve for the sea water inlet.
Connect the battery. Run the engine for two minutes and check for leaks. Check the coolant level in the expansion tank.Naturally Aspirated Engines
Illustration 3 g00758488
Put the heat exchanger into position and install bolt (9) to the support brackets.Note: If the brackets have been removed, apply Loctite 603 to the bolts that attach the brackets to the cylinder block.
Install two bolts (10) at the front of the heat exchanger to the support bracket.
Illustration 4 g00743803
Install two bolts (7) that fasten the transmission oil cooler to the heat exchanger.
Install water temperature regulator housing (8) onto the heat exchanger. Slide hose (4) into position and tighten the hose clamps.
Slide hose (2) into position and tighten the hose clamps.
Slide hose (3) into position and tighten the hose clamps.
Install hose (5) and hose (6) onto the heat exchanger and tighten the hose clamps.
Slide hose (1) into position and tighten the hose clamps.
Install the drain plug for the engine coolant. Install the drain plug for the sea water circuit.
Fill the cooling system. If the engine uses diesel engine antifreeze/coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses extended life coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Open the valve for the sea water inlet.
Connect the battery. Run the engine for two minutes and check for leaks. Check the coolant level in the expansion tank.