7N6272 GOVERNOR FUEL INJECTION AND FUEL TRANSFER PUMP GROUP Caterpillar parts
988B
Rating:
Alternative (cross code) number:
CA7N6272
7N-6272
7N6272
CA7N6272
7N-6272
7N6272
Weight: 0.01 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 7N6272:
Number on catalog scheme:
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Removal Procedure
Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g01191733
Remove cover (1) .
Illustration 2 g01246508
Disconnect electrical connector (2) .
Illustration 3 g01246507
Disconnect five hose assemblies (3) from service brake control valve (4) .
Illustration 4 g01246511
Remove four bolts (6) and mount (5) .
Illustration 5 g01246513
Remove two nuts (7) .
Remove service brake control valve (4) .
Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g01191733
Remove cover (1) .
Illustration 2 g01246508
Disconnect electrical connector (2) .
Illustration 3 g01246507
Disconnect five hose assemblies (3) from service brake control valve (4) .
Illustration 4 g01246511
Remove four bolts (6) and mount (5) .
Illustration 5 g01246513
Remove two nuts (7) .
Remove service brake control valve (4) .
Parts governor Caterpillar catalog:
7N6271
GOVERNOR GP
3408, 3412, 988B
3408, 3412, 988B
8N7526
GOVERNOR GP
3408, 3412, 772B, 773B, 988B
3408, 3412, 772B, 773B, 988B
3408, 3408B, 3408C, 3412, 3412C, 3412D, 772B, 773B, 775B, 834B, 836, 988B, 988F
4N1894
GOVERNOR GP
3408, 3412, 988B
3408, 3412, 988B
7N1239
GOVERNOR, FUEL INJECTION PUMP AND FUEL TRANSFER PUMP GROUP
631D, 633D, 637D
631D, 633D, 637D
6N5178
GOVERNOR GP
3408
3408