4525996 GREASE-5 PCT M Caterpillar parts
Rating:
Alternative (cross code) number:
CA4525996
452-5996
4525996
CA4525996
452-5996
4525996
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$178.89
23 Nov 2021
US: Omskva
SMC Round Body Air Cylinder - Standard - Standard, Double-Acting.4375 in Rod Size, 1.5000 in Bore Diameter, 10.0000 in Stroke Length, Block Mount
Generic bore diameter: 1.5000 in || operating temperature range: 40 F to 140 F || piston action: Double-Acting || overall length: 15.44 in || cylinder size: Standard
Generic bore diameter: 1.5000 in || operating temperature range: 40 F to 140 F || piston action: Double-Acting || overall length: 15.44 in || cylinder size: Standard
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 390-1131 Crankshaft Locking Pin 1
B 435-3146 Camshaft Locking Pin 1
C - Balancer Timing Pin
(Bolt M8 by 22mm) 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Check that the balancer drive gear is not worn or damaged. If necessary, replace the balancer drive gear.
Illustration 1 g03774859
Illustration 2 g03774861
Illustration 3 g03774862
Install Tooling (A) into Position (Y) in the cylinder block. Note: Failure to locate the crankshaft in the correct position will cause severe engine damage.
Install Tooling (B) into Position (X) in the front housing.
Ensure that Tooling (C) is installed to balancer (6). Note: New balancers will be supplied with Tooling (C) in position.
If necessary, install dowels (11) to balancer (6).
Attach a suitable lifting device to the balancer. The weight is approximately 15 kg (33 lb).
Use the suitable lifting device in order to install the balancer to the cylinder block.
Install bolts (7) to the balancer. Tighten the bolts to a torque of 70 N m (52 lb ft).
Remove the suitable lifting device from the balancer.
Install a new O-ring seal (10) onto suction pipe (5). Install the suction pipe assembly to the cylinder block.
Install bolt (9) finger tight.
Install bolts (8) finger tight.
Tighten bolt (9) to a torque of 10 N m (89 lb in)
When M8 bolts are installed, tighten bolts (8) to a torque of 25 N m (221 lb in). When M10 bolts are installed, tighten bolts (8) to a torque of 45 N m (33 lb ft).
Remove Tooling (C) from Position (Z) in the balancer.
Remove Tooling (A) from Position (Y) in the cylinder block.
Install a new O-ring seal (4) to plug (3). Install plug (3) into Position (Y) in the cylinder block. Tighten the plug to a torque of 50 N m (37 lb ft).
Remove Tooling (B) from Position (X) in the front housing.
Install a new O-ring seal (1) to plug (2). Install plug (2) into Position (X) in the front housing. Tighten the plug to a torque of 25 N m (221 lb in). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Name Qty
A 390-1131 Crankshaft Locking Pin 1
B 435-3146 Camshaft Locking Pin 1
C - Balancer Timing Pin
(Bolt M8 by 22mm) 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Check that the balancer drive gear is not worn or damaged. If necessary, replace the balancer drive gear.
Illustration 1 g03774859
Illustration 2 g03774861
Illustration 3 g03774862
Install Tooling (A) into Position (Y) in the cylinder block. Note: Failure to locate the crankshaft in the correct position will cause severe engine damage.
Install Tooling (B) into Position (X) in the front housing.
Ensure that Tooling (C) is installed to balancer (6). Note: New balancers will be supplied with Tooling (C) in position.
If necessary, install dowels (11) to balancer (6).
Attach a suitable lifting device to the balancer. The weight is approximately 15 kg (33 lb).
Use the suitable lifting device in order to install the balancer to the cylinder block.
Install bolts (7) to the balancer. Tighten the bolts to a torque of 70 N m (52 lb ft).
Remove the suitable lifting device from the balancer.
Install a new O-ring seal (10) onto suction pipe (5). Install the suction pipe assembly to the cylinder block.
Install bolt (9) finger tight.
Install bolts (8) finger tight.
Tighten bolt (9) to a torque of 10 N m (89 lb in)
When M8 bolts are installed, tighten bolts (8) to a torque of 25 N m (221 lb in). When M10 bolts are installed, tighten bolts (8) to a torque of 45 N m (33 lb ft).
Remove Tooling (C) from Position (Z) in the balancer.
Remove Tooling (A) from Position (Y) in the cylinder block.
Install a new O-ring seal (4) to plug (3). Install plug (3) into Position (Y) in the cylinder block. Tighten the plug to a torque of 50 N m (37 lb ft).
Remove Tooling (B) from Position (X) in the front housing.
Install a new O-ring seal (1) to plug (2). Install plug (2) into Position (X) in the front housing. Tighten the plug to a torque of 25 N m (221 lb in). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Parts grease Caterpillar catalog:
4434946
GREASE
Caterpillar
Caterpillar
4429084
GREASE
Caterpillar
Caterpillar
4241489
GREASE-
Caterpillar
Caterpillar
4241488
GREASE-
Caterpillar
Caterpillar
4241487
GREASE-
Caterpillar
Caterpillar
4241486
GREASE-
Caterpillar
Caterpillar
4526020
GREASE-LOW TEM
Caterpillar
Caterpillar
4526014
GREASE-UTILITY
Caterpillar
Caterpillar
Caterpillar
4526009
GREASE-3 PCT M
Caterpillar
Caterpillar
4526006
GREASE-
Caterpillar
Caterpillar
4525997
GREASE-5 PCT M
Caterpillar
Caterpillar